- Joined
- May 28, 2020
- Messages
- 1,673
- Likes
- 6,588
- Thread Starter
- #121
Yup, $1699Do you have any ballpark pricing yet on the 3 channel? Thanks.
Price may come down slightly, depends on the final price of the input board. But it won't go up
Yup, $1699Do you have any ballpark pricing yet on the 3 channel? Thanks.
Do you mean the cases with the input boards?Do you think the 3 channels will use the new cases/will the 2 channels be offered in the new cases?
Yes? I meant the vertical alignment cases for the new NCxxxMP amps, currently the Purifi's are slated to be shipped with the older standard case used for the NCxxxMP amps right?Do you mean the cases with the input boards?
The 2 and 3ch Purifi's will be utilizing a custom input buffer board with the same features of the NCxxxMP revisions (Auto on, microcontroller control, etc)
Yes. The vertical alignment case is mainly an option for the 8ch NC502, though customers can request to use it for any NCxxxMP configuration at an additional cost.Yes? I meant the vertical alignment cases for the new NCxxxMP amps, currently the Purifi's are slated to be shipped with the older standard case used for the NCxxxMP amps right?
Ah, as in there is a single size with vertical alignment (sufficiently large for 8 channels). I thought perhaps you might get those cases in additional sizes (2, 3/4,5/6, and 8).Yes. The vertical alignment case is mainly an option for the 8ch NC502, though customers can request to use it for any NCxxxMP configuration at an additional cost.
Puce…I personally would vote for scarlet and gray.
Typo - = 3ch, not 2 for $1699Our brand new 2ch and 3ch Purifi amplifiers are well underway! Pre-orders are now open!
2ch specs are as follows:
(2) Purifi 1ET400A modules
(1) Hypes SMPS1200A400
10"x12"x3" Aluminum chassis (same type used on my current Hypex amps)
*speakON option available
3ch specs are as follows:
(3) Purifi 1ET400A modules
(1) Hypes SMPS1200A400
Aluminum chassis (same type used on my current Hypex amps) - Dimensions TBD
*speakON option available
Custom Input Buffer Board w/:
- Neutrik XLR connectors
- OPA1612 OP Amps
- TI Voltage Regulators
- Low, Med, High Gain settings
- Auto On (along with Always On and 12v options)
2ch Price = $1189 shipped (in the US...extra shipping cost for international orders)
2ch Price = $1699 shipped (in the US...extra shipping cost for international orders)
Finally, the official Buckeye Amps Website!
The debugging/testing on the 2ch Purifi Input Buffer Board is complete and a prototype build is being sent out for measurements (not to Amir but a 3rd party to diagnose any issues before a final production unit).
I can confirm the Purifi board allows both clipping indication and error state indication, which from what I have been told is something most other Purifi builds out there do not offer.
Agreed but the cost to incorporate it since an MCU was already on the board was very very minimum. Just an extra feature to advertise for the few who want to have it.While indicator lights are cute. They really are not needed. If you can clip a Purifi amp in normal use then you are playing MUCH louder than I enjoy.
Yup!Any plan to off the 700 version as well?
I amWow… the 700 version should only be useful for people regularly driving 2 to 3 ohms. There is really no benefit at 4 to 8 ohms load.
Are you actually taking pre-orders for the 3 channel version of the 1ET400a?
2ch prototype layout.
Waiting on some cables and need to revise the case cutouts slightly for mounting.
They do as an upgradeable option during purchaseLooks good but I thought these were going to have speakon connectors???