- Joined
- May 28, 2020
- Messages
- 1,673
- Likes
- 6,588
- Thread Starter
- #181
Not at this timeAny chance of doing a 7 channel purifi like the NAD M28?
Not at this timeAny chance of doing a 7 channel purifi like the NAD M28?
Ok, how about 11 channel like apollon thenNot at this time
Option 2Option 1:
10.5" wide x 7" deep x 2.5" high
Option 2:
7" wide x 11" deep x 2.5" high
Option 3:
8" wide x 9" deep x 4.5" high
2ch final version build (going out this week for final testing). Obviously it's missing the speaker wires and posts, and power input but wanted to show pictures of the main build layout
I'm not sure....when you look at other builds (especially larger channel builds), the PSU is not separated by anything.Would it be beneficial to have some sort of screen or shield between the modules and the PS?
2ch final version build (going out this week for final testing). Obviously it's missing the speaker wires and posts, and power input but wanted to show pictures of the main build layout
looking good, any ETA on results from final testing, and presuming testing shows no harm done (vs Arim's Purifi testing) any ETA on ship date to customers?2ch final version build going out this week for final testing.
I will have results of the final testing next week.looking good, any ETA on results from final testing, and presuming testing shows no harm done (vs Arim's Purifi testing) any ETA on ship date to customers?
So, is the testing process a five stage event?I will have results of the final testing next week.
Customer orders will be filled towards the end of June.
"Mass production" of the boards will begin before sending a unit to Amir.So, is the testing process a five stage event?
1) Send initial Beta to your tester.
2) Troubleshoot and fix any anomalies.
3) Send new revised version of Beta to Amir for a thorough secondary analysis.
4) Troubleshoot and fix any anomalies that remain using Amir's recommendations.
5) Start mass production.
I guess to be more specific with my use of the term "mass production," I mean the completed, assembled amps to paying customers."Mass production" of the boards will begin before sending a unit to Amir.
Oh I understand. However the testing I am having done next week is akin to what Amir does, just not on a public/in depth review level. If my design has any major issues or performance shortcomings, I'll know about itI guess to be more specific with my use of the term "mass production," I mean the completed, assembled amps to paying customers.
Furthermore, sending the revised assembled prototype amplifier to Amir for a second phase of testing and then fixing any flaws shown that could hamper quality or performance before assembling the amps en masse to fulfill orders.
I'm asking because it might save time and headaches later on if you sent an amp product to Amir for testing that had not been put out in the wild first, if you haven't actually gone this route. Then maybe Amir comes back with a public review that causes the need for a further revision to amps already in customers' hands. Time, money, and other problems that might have been avoided otherwise.
Inaudible differences. And almost insignificant difference in power output. At this point I care more about idle power consumption. the Purifi wins (again almost insignificant) but I don’t know about the new power supply idle spec. I like the auto-trigger-on option from Buckeye but the new Hypex has a standby power module too. Does the Nilai handle 2 ohm loads?hypex coming out with their Nilai500 kit has really jammed me up. Was planning to order two of these stereo purifi's, now not so sure...will wait to see more about the new Hypex I guess...
As long as the new Purifi builds are being thoroughly run through their paces before manufacturing starts in earnest then I'm satisfied.Oh I understand. However the testing I am having done next week is akin to what Amir does, just not on a public/in depth review level. If my design has any major issues or performance shortcomings, I'll know about it
Inaudible differences. And almost insignificant difference in power output. At this point I care more about idle power consumption. the Purifi wins (again almost insignificant) but I don’t know about the new power supply idle spec. I like the auto-trigger-on option from Buckeye but the new Hypex has a standby power module too. Does the Nilai handle 2 ohm loads?
and you still have to build it yourself...
I consider that a plus, actually, especially considering I need a 4 channel amp so it may be cheaper actually considering I won't need to pay for 2 cases, etc.