Transfluxor
New Member
- Joined
- Sep 4, 2019
- Messages
- 2
- Likes
- 0
Did I understand correctly that the load impedance when testing Mojo was 600 Ohms?
I mean a test from Amir.
I mean a test from Amir.
Last edited:
Check out the recommended list https://www.audiosciencereview.com/forum/index.php?threads/amirs-recommended-list.8949/ within your budget.Hi, congratulations for your reviews.
I have Mojo and i'm very happy (with headphone Beyerdynamcs DT990 32 ohms). It's my first system audiophil.
If i want to upgrade my system, around 300€, what can you advise me to replace my Mojo ? (3 models portable and 3 models desktop ?). Sorry for my question very simplist...
Best regards.
I've heard some people here prefer khadas tone board ($90) to their mojo, prompting selling off their mojo. Khadas tone board or Topping D50s + JDS Atom amplifier is very good value $200 stack. DX3 Pro is very good combo device, but some have had reliability issues. If you want a combo device the DX3 pro is great though, also has bluetooth. Sabaj D5 has XLR outputs if you want balanced output. Topping DX7s like D5 is balanced, will soon be upgraded with better specs and bluetooth if you can wait and want bluetoothThank you very much for your answer. I'm happy with mys system. The reason is just i'm curious to go further to hear an even better sound in the audio. After eventually sold Mojo...
Thanks again.
Do not forget about the load impedance. A decrease in impedance leads to a significant increase in distortion. Why was Mojo tested with a load impedance of 600 Ohms but was placed on the general SINAD list where all or almost all devices were tested with a load impedance of 100 kOhm? This is obviously a losing situation for Mojo.Amirm wrote on his test report:
"This review will be much more detailed than my usual ones since Chord DACs are sold on basis of technical claims. As I typically do, I start with testing the DAC portion of the unit and then the headphone amplifier. Since there is no separate line out, I resort to setting the output to 2 volts. There is a mode to put the unit in "line-out" mode but it produces too high a voltage of 3 volts which degrades the performance. I don't know where the notion of 3 volt comes from other than wanting to make sure the unit sounds louder than others."
Looking at the Golden Ears test report few pages back, they have most likely used the 3 v line level. Those graphs don´t show any performance degradation. Would some one like to clarify what performance degradation is meant by this?
(I understand the testing with 2V to be comparable with others, just a little confused about the statement. I use 3v line out with a amp that can take it. No audible difference with 2V other than volume)
Why was Mojo tested with a load impedance of 600 Ohms but was placed on the general SINAD list where all or almost all devices were tested with a load impedance of 100 kOhm? This is obviously a losing situation for Mojo.
Ugggg... was not aware Chord was part of the + 5000 GBP Club for "interconnects". The only way a cable will mess up your sound is if it has a short in it. Any cable made to standard and not longer than really needed will transfer the electrical current perfectly. That's why so many people talk about wanting an amplifer that is basically just a wire with gain! (I know, preaching to the choir.)
Mojo is really hyped everywhere I read about it, people say it sounds very full and pleasant... I would really like to hear it and compare it to Topping D30 but I can't justify buying it just out of curiosity right now.
Hum.In the past we had awfully sounding power amps with astounding measurements, high power, and incredible amounts of global feedback. Measurements are not most important factor when choosing a component, otherwise we would still use those power amps. But they are proof of good engineering once the sound is also subjectively correct and non fatiguing.
I do not understand some of the critics.
Thanks for publishing.At 1 kHz with 0 dB (~2Vrms) we achieved 0.00031%, ~ -110dB
That's a typo on my part, the output was attenuated to 2 Vrms from 3 Vrms nominal using AVI S2000MCI'm confused, before edit it said 'at 0fbfs (~3Vrms)', which is it? 3Vrms would have better SNR.
Aha OKThat's a typo on my part, the output was attenuated to 2 Vrms from 3 Vrms nominal using AVI S2000MC
That's great - then only a smartphone with optical output has to come onto the market .....Nice job! I guess optical is the way to go with Mojo, as Rob Watts has been telling us.