Probably yes, because the store is included in the authorized resellers: https://www.tpdz.net/aliexpressMaybe @JohnYang1997 can confirm if this is legit, but I bought a replacement for mine in this link from Aliexpress:
Probably yes, because the store is included in the authorized resellers: https://www.tpdz.net/aliexpressMaybe @JohnYang1997 can confirm if this is legit, but I bought a replacement for mine in this link from Aliexpress:
The L30 has a three-position gain switch. It also has plenty of power. I sincerely doubt there's anything better for headphones that don't need balanced connection to the amp. It's still the THD + Noise champion of headphone amps.is it a good amp for my sundara ?
Sundara has low impedence (37 Ohm) and L30 doesnt have a gain switch... is there any better solution up to 150 euros ?
Good choice toowhat about against JDS Labs Atom+ ?
I would recommend reading the respective reviews, comparing the feature sets, availability, warranty/service and picking the one that suits your needs the best. Either way, both will be audibly transparent.what about against JDS Labs Atom+ ?
It's a great combo, I used my Sundaras with the L30 and I was really happy with the combo.is it a good amp for my sundara ?
Sundara has low impedence (37 Ohm) and L30 doesnt have a gain switch... is there any better solution up to 150 euros ?
For low impedance headphones L30 can delivers more current than Atom (Plus) hence more power but you will need a DAC capable to output a signal up to 3V to make it reachs its maximum power. Atom is limited to ~1W at 32ohm because it saturates (clips) in this condition, L30 does not. It's possible to compare both amps using Atom Plus and Sabaj A10h (almost the same circuit from L30) reviews. At the THD+N vs output voltage A10h doesn't saturate indicating it has some headroom to output more power.I would recommend reading the respective reviews, comparing the feature sets, availability, warranty/service and picking the one that suits your needs the best. Either way, both will be audibly transparent.
Thank you!It has already been discussed here. It is a measurement error caused by the measurement method Marv used.
It is the back EMF of a headphone falling across a small resistance you are looking at.
As you can see the thread went silent after my HD650 load simulator was built.
The l30 in preamp mode in high gain (+9db) will drive the pa5 to full power no problem in your setup.I asked the same question on the PA5 Review thread but it got buried.
What is the output voltage of the L30 in pre-amp mode?
I read through the documentation but I got confused and wasn't sure what to make of it.
Amir mentioned the PA5 needs 2.5V signal going into to be driven effectively (to achieve max power).
I'm using an E30/L30 stack, and was considering expanding to a desktop speaker setup adding a PA5 and passives to my mix.
Want to know if I need to pass the signal through the L30 as a pre-amp or it can be skipped altogether, and what the ramifications are to my signal.
Thanks.
Which screws you have picked to measure? The screws closer to the RCA connectors are not connected to ground, those close to case's edges are supposed to be...Please help.
I just bought a (New) Topping L30 from a UK eBay seller. It came in the original box and was well packed.
It has a 201262 number but doesn't have continuity between the channel ground and the back panel screws.
Is it easy to fix with a ground wire or should I send it back?
I'm very suspicious that it's a customer return item that's being resold.
What should I do?
Any resumen?@amirm I was wondering if you could give me an explanation about what I read in this topic?
Oh shit! SINAD can suck my ****s
With the recent acquisition of an AP analyzer, my intention was to leverage its automation capabilities to offer an alternative more developed set of...www.superbestaudiofriends.org
Please help.
I just bought a (New) Topping L30 from a UK eBay seller. It came in the original box and was well packed.
It has a 201262 number but doesn't have continuity between the channel ground and the back panel screws.
Is it easy to fix with a ground wire or should I send it back?
I'm very suspicious that it's a customer return item that's being resold.
What should I do?