Search results

I've successfully used USB mics with acoustic timing reference, but I noticed that I get best results when I used a small speaker placed close to the microphone and not move them around between measurements (DUT can be rotated if doing off-axis). I previously used the other speaker of a stereo...

In the first post, the picture with plywood, they are on a Volkswagen.

That's a Volkswagen Passat.

As far as I know, by following REW instructions you can make meaningful measurements with USB mics, but they are valid and comparable only for the session. Anything that involves a microphone depends on how the mic is placed, so if you swap a speaker you will have invalidated comparability...

So is this a valid meme now? J/k ;)

In short, this is what I know. Both passive radiator (PR) and reflex port are means of bass reflex tuning. And that is one way to do equalizing. Both methods have their strengths and weaknesses. A few worth mentioning are 1) a port increases sensitivity above tuning frequency, 2) port produces...

Yeah, I use a 350 € phone daily and own a UMIK-1.

You have a thousand dollar phone, but complain about price of UMIK-1???? Some things to consider: the use of a measurement mic is seldom one-time. It will most likely outlive your current phone. The most useful part of a proper mic is that you can use it with proper software on a real computer...

Yes, exactly this, thank you. I currently have 12 speaker drivers in my home, but none of them are in a ported box So the 2nd and 3rd harmonics are 10-15 dB below fundamental. That makes air a lousy membrane, eh...

@amirm I have a request: Could you measure the sound from the port more thoroughly, please? Just even once, on this or the next ported speaker you measure. I'm most interested in the harmonic distortion that comes from the port, at different sound pressure levels. I'm not sure if it makes a...

It's a center speaker, it's main job is to disperse sound horizontally, so you should give that more weight. Headless.

People who speak against 15" or larger have not witnessed a 15" or larger playing. You can get 20 Hz from 4", but it's -20 dB below 1 kHz and over excursion happens at 85 dB. With dual 15" per side you can expect 90+ dB with 1 Watt and capacity that does not give in. 15" can have 15 mm xmax...

Nice setup Speaking of which, I own two Arendal 1723 Subwoofer 1 subs. I wanted to build 15" bass legs between my 2-way mains and the subs, to give more performance below mid-range and above subwoofer range. So I got a pair of 15 inchers, put them on 80 l boxes and fired up the DSP and some...

Hi everyone. I have an opportunity to acquire one or two PA5 units for a very low cost (less than 50 €). So I was wondering if getting and fixing them would be worth the effort, even though I have no immediate need for them. I would soon need a small amp for my work desktop set. I have one...

I once looked at Neurochrome and after comparing the apples to a battlecruiser I decided that it's not worth it. The alternative build totals for less and you can put it in a box too.

Have no fear, the volume knob is there! When comparing 10 W amp to a 100 W amp, that is the maximum power that the amplifier can provide. It does not mean that the latter is 10 times louder (gain) than the former. It's also up to how much the speaker "draws" power (impedance), so high impedance...

I'm a DIYer and all the speakers I currently use are DIY, so my needs are probably not as common as for many others. My best speakers use Hypex plates, so digital inputs from preamp is a necessity. For that I use currently miniDSP SHD. I would not be trading these away easily, so anything I...

If anyone needs audio routing and processing for a PC, I'd suggest Voicemeeter. It's got varying complexity levels per app, like the standard, Banana and Potato. There is also the Virtual Audio Cable, that does only point to point routing. I've had good experience with these before. Donationware.

No, this is perfect. If I got paid for drinking wine and eating good food while screwing electronics on a whim, I'd go for it sure. Joking aside, at least he says he is tweaking component values, which are measurable

What kind of hardware did you end up using? Do you have an addon board that handles power supply or do you feed with possibly with splitter cable? One of my requirements os usb input. I cannot use BT (like in JAB5 or KABD-4100), because it's got a ~500 ms sleep timer on Windows 10, which I...