Search results

The following may be self evident, but for clarity, there seems to be 3 separate categories in the specs discussed above: 1.minimum specs to allow standardization of measurement: you need every measured DAC (or preamp ‘out’) to have a minimum unbalanced output of 2V to fairly compare them. same...

The M2 has a max output of 16dBu for TRS output and 9.5dBu by RCA. The Yamaha monitor input sensitivity is -10dBu. When you turn up the volume past a certain point you far exceed the maximum voltage the Yamaha allows. That’s why the speakers distort.

Ideally, you want to go from low impedance to high impedance so there is less power loss and less frequency range error. That said 600 ohms going into 2.5Kohm for the XLR input is a reasonable ratio: you’ll get 80% of the voltage you would compared to the TRS. You won’t break anything, so if...

Thank you so much for sharing your insights. I was wondering whether you ever looked at intra-observer scoring variability over time. My impression is that our subjective enjoyment of sound varies tremendously based on our mood, type of music, playback volume, expectations (big expensive...

Does anyone know of any good binaural recordings? I’m curious to listen to that with headphones to see how it sounds. I suspect it works best if the dummy head has similar head and canal shape to the listener’s body (https://www.ncbi.nlm.nih.gov/pmc/articles/PMC3561850/).

Yes, that totally makes sense it would reduce time and effort to exclude some participants. I’m just saying that ideally you would state your exclusions [for example colour blind people] before you start the test. And then your conclusion will be that lipstick X is preferred by non-colorblind...

This is just a general comment on experiments, not on this particular test (the data was excluded due to improper level matching), but when it comes to this comment above, it’s not strictly correct: If you want a valid experiment, data cannot be screened out once a study has started. All...

You may have already discussed your methodology elsewhere, so sorry if I repeat something you’ve already considered. For the next test may I suggest having each listener rate the same speaker on 3 different occasions, in blinded fashion? So if you test 5 speakers, you’d run the test 15 times...

Sorry I had misunderstood your question. Adahn’s answer was much better!!

The impedance is lower on the XLR connection. Have a look at the attached image.

Can you explain your setup a bit. Do you have a preamp between the turntable and the motu (I’m guessing you don’t). If you don’t do you have a a step up transformer for impedance matching (because your cartridge may not play optimally at the impedance of the motu’s input). if you use the trs...

The XLR ports are mono. Have you pushed on the monitor button next to the input? If so the mono signal will be sent to both r and l channels.

Amir, If you still have the unit and have the time, can you please run a SINAD on the mic input with gain turned up to max? Just curious about the performance of the mic amp for conducting measurements for DSP room corrections.

@amirm I wonder if measuring a few loudspeakers at ~10 feet with this system might provide some interesting data (sort of a summation of direct and indirect sound). I realize there are no standards to compare to, but measuring a few well behaved speakers and some crappy speakers might yield...

I I have two Ahb2 amps connected in bridged mono, so I can have 4 channels of amplification to do a digital XO if I want to. My DAC is a MOTU8a which is multichannel, so no problem there. My sub is powered separately. Maybe I should just go for it. Are the woofers typically just screwed in...

I think my living room is my chain's main weakness, but I'm always curious about how to improve my system. I have a pair of Tannoy GR stirling speakers. I generally like how they sound; there is something about coaxial drivers, a single point source that works well for me. However, a couple of...

Hi Mitch, I was looking at your measured room response and was really impressed at your results (flatter freq response, with less dB correction than my setup). I figured I'd check out your speakers for interest, and noted your were selling them on canuck audiomart. I hope I'm not being too nosy...

Olli, Have you tried your Motu with Roon? My Roon server is on a NUC running ROCK. I read some forum posts about people having some communication problems between Motu DACs and systems running linux. Of course it's hard to know if it's an operator problem, or a real issue.

Mitch’s article is what got me started exploring DSP. I got his book too. He uses JRiver and a Hilo lynx Dac. The way I’ve gone about it, I notice the time delay between the 3 streams varies a tiny bit. Not sure if it’d be audible but it bugs me. If Roon could have played 6 channels on a...

Yes that’s how I’ve implemented my filters so far. Because the source material is 2.0 stereo, I’ve had to have 3 DSP filters (tweeter, woofer, sub) with 3 different zones. The 3 zones are grouped together. My NUC PC running Roon then outputs to 3 zones ie 3 outputs simultaneously (tweeter via...