• Welcome to ASR. There are many reviews of audio hardware and expert members to help answer your questions. Click here to have your audio equipment measured for free!

Trinnov AltitudeCI Review and 32 Channel Build Thread

Reddit doesn't know much as usual. ;)

I'm 6 feet from the LCR, that's perfectly in line with the usual 6-8 feet generally recommended for the best stereo imaging. If you study pics from the best sudios in the world, many are setup like that, and most aim the height speakers just as I have. My stereo image extends past 180 degrees. Atmos is truly immersive as are 5.1 tracks. I know all this sounds unbelievable, but drop me a PM if you are close to South Carolina.

Had the Palladiums for many years. All were bought used. I buy them used whenever I see some that are on the cheap side. Nothing beats them, especially at 70-90% off retail. Very few ever go on sale though, and that should already tell you something. Honestly, I wouldn't own anything else.

Daaaamn many things to be impressed with, but them Palladiums is just a wet dream.
When did you get them? Why did you pick them? They do deserve a bigger space for sure. I bet they rock!
 
Last edited:
Reddit doesn't know much as usual. ;)

I'm 6 feet from the LCR, that's perfectly in line with the usual 6-8 feet generally recommended for the best stereo imaging. If you study pics from the best sudios in the world, many are setup like that, and most aim the height speakers just as I have. My stereo image extends past 180 degrees. Atmos is truly immersive as are 5.1 tracks. I know all this sounds unbelievable, but drop me a PM if you are close to South Carolina.

Had the Palladiums for many years. All were bought used. I buy them used whenever I see some that are on the cheap side. Nothing beats them, especially at 70-90% off retail. Very few ever go on sale though, and that should already tell you something. Honestly, I wouldn't own anything else.
Nice. i did see some palladium speakers and even subwoofers on audiomart website but obviously the 5.2 system was super expensive. i think it was close to 10 grand used and I believe there is zero replacement for anything.
 
Yeah, good thing those are in CA and not close to me lol. I'd haggle and buy the P-39f's without the sub if I could work out a cash price and pick them up in person.

i did see some palladium speakers and even subwoofers on audiomart website
 
I watched most of the youtube video above today. At some point the audiophile jargon was too much for me and I skipped forward. But much more importantly this is one of the few pieces I’ve seen from the major high end magazines that attempts to move things forward in way that’s consistent with proper engineering and physics.

It’s a shame how much energy is expended on solutions that simple don’t address the problems they attempt to solve. Interestingly the world of home theater is much more science based, and now with DSP evolving to more sophisticated technologies, the timing is right for displacement of the hi end snake oil products.
 
BWfFBlMqGmM
Thanks for the video link. It was quite interesting, if rather indulgently long.
He seemed to be obsessed with the idea that better bass improves imaging and sound-staging.
Better bass is always good, but I think it's more accurate to say it's Trinnov that improves both bass and imaging.
 
I think there are several technical reasons why properly optimized bass can improve perceived imaging and soundstage in virtually any system, particularly when crossing the mains over to multiple subwoofers (see points 1 thru 3 below). I noticed this improvement even before getting my Trinnov. However, the AltitudeCI further refined the imaging compared to my previous setup, where I had five subwoofers producing a response within approximately ±5 dB without EQ. Of course, good room correction can improve imaging, just as treating first-order reflections with absorption and using diffusion to control reflected energy can also improve spatial clarity.

1. Reduced masking and improved spectral balance:
Excessive modal peaks and prolonged bass energy can mask quieter musical details and alter tonal balance, potentially obscuring spatial information and instrument separation.

2. Improved temporal behavior:
Reducing high-Q modal peaks can also reduce associated ringing and prolonged decay, improving clarity and reducing interference with subsequent sounds.

3. Independent optimization of room modes:
Main speakers are positioned primarily for imaging, not optimal modal excitation. Multiple distributed subwoofers provide greater control over how room modes are excited, reducing peaks, nulls, and low-frequency response differences between channels that might otherwise be unavoidable with full-range mains.

None of this necessarily improves the direct localization cues reproduced by the mains. Rather, reducing room-induced coloration, masking, and prolonged decay may allow the spatial information already present in the recording to be perceived more clearly. The rest of the story is clearly Trinnov's Optimizer though.

Thanks for the video link. It was quite interesting, if rather indulgently long.
He seemed to be obsessed with the idea that better bass improves imaging and sound-staging.
Better bass is always good, but I think it's more accurate to say it's Trinnov that improves both bass and imaging.
 
Hopefully. Probably why ASR and this thread is the top search result when I google "Trinnov Altitude CI review" lol. But good luck with teaching some folks. But, it's a free country, if they want to spend their money on cables they can.

It’s a shame how much energy is expended on solutions that simple don’t address the problems they attempt to solve. Interestingly the world of home theater is much more science based, and now with DSP evolving to more sophisticated technologies, the timing is right for displacement of the hi end snake oil products.
 
I think there are several technical reasons why properly optimized bass can improve perceived imaging and soundstage in virtually any system, particularly when crossing the mains over to multiple subwoofers (see points 1 thru 3 below). I noticed this improvement even before getting my Trinnov. However, the AltitudeCI further refined the imaging compared to my previous setup, where I had five subwoofers producing a response within approximately ±5 dB without EQ. Of course, good room correction can improve imaging, just as treating first-order reflections with absorption and using diffusion to control reflected energy can also improve spatial clarity.
I think all those things are certainly true. Years ago I used to move both my speakers and my listening position as far away from the walls as I practicably could, and that helped both the bass evenness and stereo image reproduction. I considered walls to be mirrors that reflected the rays being transmitted in all directions by the speakers, and if I was closer to the actual speakers and further away from all the reflections of the speakers, then the direct ray-paths were shorter and less affected by the reflected ones.

With Optimiser (and Dirac) the emphasis is on how to manage the room, especially in the bottom decade where wavelengths are longer. However I think good EQ can help the speakers themselves, and can help the middle decade, as well. From everything I've heard, that helps sound-staging over and above the improvements to the bass. In the case of the video, where some large three-way Perlisten speakers were being used, I think there was a lot to gain. The most expensive speakers are often the worst offenders. How many times have people said that small budget stand-mount speakers have great imaging?

I've been following this thread with great interest, from a distance, for a long time. It's interesting to see what can be accomplished.
 
I think there are several technical reasons why properly optimized bass can improve perceived imaging and soundstage in virtually any system, particularly when crossing the mains over to multiple subwoofers (see points 1 thru 3 below). I noticed this improvement even before getting my Trinnov. However, the AltitudeCI further refined the imaging compared to my previous setup, where I had five subwoofers producing a response within approximately ±5 dB without EQ. Of course, good room correction can improve imaging, just as treating first-order reflections with absorption and using diffusion to control reflected energy can also improve spatial clarity.

1. Reduced masking and improved spectral balance:
Excessive modal peaks and prolonged bass energy can mask quieter musical details and alter tonal balance, potentially obscuring spatial information and instrument separation.

2. Improved temporal behavior:
Reducing high-Q modal peaks can also reduce associated ringing and prolonged decay, improving clarity and reducing interference with subsequent sounds.

3. Independent optimization of room modes:
Main speakers are positioned primarily for imaging, not optimal modal excitation. Multiple distributed subwoofers provide greater control over how room modes are excited, reducing peaks, nulls, and low-frequency response differences between channels that might otherwise be unavoidable with full-range mains.

None of this necessarily improves the direct localization cues reproduced by the mains. Rather, reducing room-induced coloration, masking, and prolonged decay may allow the spatial information already present in the recording to be perceived more clearly. The rest of the story is clearly Trinnov's Optimizer though.

I would add 4) specifically for Waveforming.

Best way to explain it is “directionality” of the bass, where front to back emitter/absorber configuration makes it feel like energy is coming from the mains. It makes all the bass instruments anchored in space in fornt of you, very precisely. From measurements perspective there is no Group Delay, outside of drivers own GD. This removal of modal resonances, that are normally arriving from every direction makes very audible difference,

What I enjoy [if it is included in the recroding] is depth of bass [and subsequently whole soundstage] and it also gives 3rd dimension to instruments [so there are not onxly strings, but also big body of double bass.
 
However I think good EQ can help the speakers themselves, and can help the middle decade, as well. From everything I've heard, that helps sound-staging over and above the improvements to the bass.
Oh definitely, EQ made a difference in my setup. I also did everything possible as far as speaker setup before I ever used EQ. I have FL and FR toed in, 3.38 feet from front wall to front of speaker, treat first order reflections, etc...

Best way to explain it is “directionality” of the bass, where front to back emitter/absorber configuration makes it feel like energy is coming from the mains.

Yep, I think that comes from several things: 1. proper mains to sub integration (very smooth phase response through the XO region) 2. very fast decay times and accurate bass. I have subs distributed throughout my room, and you'd swear you can pinpoint bass from drums, etc... in the image.
 
New firmware is out. Anyone try it?

AltitudeCI 2.2.1
Bug fixes
• Fixed a clock synchronization issue. The problem showed up on the interface as the display alternated between “NO SYNC” and the clock frequency.
Known limitations & bugs
• Roon and UPnP inputs are not supported yet.
• La Remote is not functional.
• The save process can sometimes take a long time with a spinner displayed on the interface.
• OSD is currently not available.
• Upmixing native Dolby content with Neural:X or Auro3D may result in playback issues or complete loss of audio.
• If the image fails to display after waking the device, go to SOURCES/HDMI and press 'Refresh' EDID.
• Speaker groups checkboxes can’t be clicked on the following pages :
• target curves
• extension curves
• FIR EQ
• Graphic EQ


• When entering calibration with dim. activated on the interface, dim. mode wrongly stays effective during calibration.
• HDMI resolution and colour information displayed on the interface are sometimes incorrect.
• Issue when using the load PEQ feature on a multiway speaker : the PEQ can be affected the wrong way.
• Changing preset when using the graphs page doesn’t automatically reload graphs. The app needs to be refreshed for them to be displayed correctly.
 
@Kal Rubinson

Couldn't wait, so I installed it. HDMI clicks between Atmos tracks are gone now (I never enabled the mute feature that would have been a temporary fix). I'm still keeping AES for music though as I already wrote a JRiver plugin that switches between AES and HDMI automatically, plus RME's ASIO driver and TotalMix are too great to live without. I do limit AES to 96kHz, but the CI is 100% solid. Using a Windows 10 LTSC PC. I updated the first post here with more details if you are curious.
 
Glad they isolated it and fixed the firmware issue. I could calibrate mine before though.

Yes, since it impacted me. I couldn't calibrate on 2.2 because of the clock sync issues. That's fixed now. So I went from 2.1 to 2.2, so far, so good.
 
Last edited:
If you go to Trinnov Altitude [not CI] forum on AVS, there is a discussion about bug in Optimizer filter settings - impulse and polarity.

It seems, that CI is also affected and will be corrected with 2.3 update.
 
Yep. Just one more reason to invest in a decent measurement rig. I still have serious doubts a USB mic will be phase accurate and have ultra low distortion... Investing in my measurement setup in 2017 was well worth it. FWIW, I did have to correct delays on my setup, but not that much. I did totally throw out the automatic tri-amp settings and go manual though :)

If you go to Trinnov Altitude [not CI] forum on AVS, there is a discussion about bug in Optimizer filter settings - impulse and polarity.

It seems, that CI is also affected and will be corrected with 2.3 update.
 
FWIW, I did totally throw out the automatic tri-amp settings and go manual though :)
Nice to hear that, since I have been a member of the "manual DSP league" all the way in my PC-DSP-based multichannel multi-SP-driver multi-amplifier full-active audio setup. :D

FWIW, just a reference for all people onboard this thread...
My present setup (ref. #931, #1,009, #1,022 on my project thread) includes "sextuple (6) amp settings," which include the L&R active subwoofers, where all the DSP tunings, including the 0.1 ms precision time alignments, have been done "manually" using my rather primitive but well-validated methods (with no black-box-type auto-processing, to me). I have also been using a measurement microphone that was strictly gain-calibrated from 20 Hz to 20 kHz.

For the details, please visit my post #931 on my project thread.
 
Last edited:
Back
Top Bottom