• Welcome to ASR. There are many reviews of audio hardware and expert members to help answer your questions. Click here to have your audio equipment measured for free!

Marantz Cinema 70s AVR Review

Rate this AVR:

  • 1. Poor (headless panther)

    Votes: 191 59.9%
  • 2. Not terrible (postman panther)

    Votes: 88 27.6%
  • 3. Fine (happy panther)

    Votes: 23 7.2%
  • 4. Great (golfing panther)

    Votes: 17 5.3%

  • Total voters
    319
The gain On Aiyima was +3 dB and the amplifier was in bypass mode. The issue is the input sensitivity. Aiyima needs 2 V of input voltage to reach its full potential, while Fosi needs only 0.7 V. Emotiva is around 1.2 V, and Vibelink is about 2.7 V.

Regarding sound quality, they are quite similar. Aiyima might be slightly better when Fosi is using the default op-amp. However, when it comes to integrating with other speakers, Marantz works best with an amplifier that has lower input sensitivity. For example, with the Fosi at 0.7 V, I have to set the volume knob to around 90% in order to match the other speakers at 0 dB.
 
The gain On Aiyima was +3 dB and the amplifier was in bypass mode. The issue is the input sensitivity. Aiyima needs 2 V of input voltage to reach its full potential,

I highly doubt that's the issue, but if you are happy with the Fosi amp then you are all set.

while Fosi needs only 0.7 V. Emotiva is around 1.2 V, and Vibelink is about 2.7 V.

Regarding sound quality, they are quite similar. Aiyima might be slightly better when Fosi is using the default op-amp. However, when it comes to integrating with other speakers, Marantz works best with an amplifier that has lower input sensitivity. For example, with the Fosi at 0.7 V, I have to set the volume knob to around 90% in order to match the other speakers at 0 dB.

Again, if you are not going to use the Aiyma A20 then it really doesn't matter, but for the record, Amir's test show that the gain of the A20 is 25 dB. Based on that, you need 1.74 V for the amplifier to output 120 W into 8 ohms. So it is not true that "Aiyima needs 2 V of input voltage to reach its full potential", unless you define "full potential" as much more than 120 W into 8 ohms.

Input sensitivity and gain are directly related, input sensitivity is often used to indicate the input voltage required for the amp to output it's rated power. For the A20, based on their website and manual info:

It actually is rated 100 W into 8 ohms, with 25 dB gain, that means you need 1.59 V, not 2 V and if you put the gain switch to +3, you then only need 1.13 V, so there is something wrong if you found the A20 much different that the Fosi in terms of the input voltage required for the amp to output their rated output, when the +3 setting is already used.

You have to be careful with the input sensitivity specifications, because quite often manufacturers might just threw a number out such as 1.2 V, 2 V or whatever, without specifying at what load impedance and what the target, or rated output power (watts) is. Looking at gain is often better because there is less chance to get confused, or misled by the often incomplete specifications, such as Aiyima's, but then the issue is, not everyone knows how to use gain to calculate the input voltage required to achieve a given output power, it is simple to do but still, not everyone knows the math.
 
My mistake — I didn’t mean that the problem was with the Aiyima, or that this was a bad thing. What I meant is that the C70S simply can’t provide enough output voltage for the Aiyima to integrate properly.

This has absolutely nothing to do with sound quality. The issue is simply that I can’t integrate the Aiyima without setting the front speakers to +7 dB while keeping the center and surrounds at 0 dB.

As for input sensitivity, I’m going by the figures specified by the manufacturers on their websites. In general, with the Emotiva and Fosi, I can integrate the system while keeping the front speakers at 0 dB. With the Aiyima, however, they have to be set to at least +7 dB, even when the amp is in bypass mode (+3 dB).

That doesn’t make the Aiyima a bad amplifier, it simply means that it isn’t an ideal match for the C70S specifically.

Even the C70S’s internal amplification has more than enough power for my speakers, so power output is not an issue with any of these amplifiers. I’m using an external amp purely to improve the quality of stereo music playback.

For a pure stereo setup, I would always choose the A20, mainly because of its crossover and subwoofer integration, which the Fosi doesn’t have. However, in this particular setup, the Fosi turned out to be an ideal match for the C70S — especially after installing the TI OPA1656, which really made it shine.

InShot_20261007_233731870.jpg
 
Last edited:
My mistake — I didn’t mean that the problem was with the Aiyima, or that this was a bad thing. What I meant is that the C70S simply can’t provide enough output voltage for the Aiyima to integrate properly.

This has absolutely nothing to do with sound quality. The issue is simply that I can’t integrate the Aiyima without setting the front speakers to +7 dB while keeping the center and surrounds at 0 dB.

As for input sensitivity, I’m going by the figures specified by the manufacturers on their websites. In general, with the Emotiva and Fosi, I can integrate the system while keeping the front speakers at 0 dB. With the Aiyima, however, they have to be set to at least +7 dB, even when the amp is in bypass mode (+3 dB).

That doesn’t make the Aiyima a bad amplifier, it simply means that it isn’t an ideal match for the C70S specifically.

Even the C70S’s internal amplification has more than enough power for my speakers, so power output is not an issue with any of these amplifiers. I’m using an external amp purely to improve the quality of stereo music playback.

For a pure stereo setup, I would always choose the A20, mainly because of its crossover and subwoofer integration, which the Fosi doesn’t have. However, in this particular setup, the Fosi turned out to be an ideal match for the C70S — especially after installing the TI OPA1656, which really made it shine.

View attachment 563169
I understand you never said the Aiyima amp was bad or anything wrong, but I am saying that what you said about the input sensitivity of the amp did not make technical sense. Just to say "Aiyima needs 2 V of input voltage to reach its full potential" without saying what "full potential" means very little, certainly cannot explain your findings.

Also, saying "The issue is simply that I can’t integrate the Aiyima without setting the front speakers to +7 dB while keeping the center and surrounds at 0 dB." means again, very little, without knowing the sensitivity of the front speakers versus the center speakers versus the surround speakers and their distance from your seat.

Lastly, "C70S simply can’t provide enough output voltage.....", makes little sense either, as the C70S can output close to or higher than 4 V rms, so it is highly unlikely that it cannot provide enough output voltage.

To be clear, I am only raising these points trying to understand the underlying reasons for your findings, and based on available information so far, something else is wrong, other than the "input sensitivity" of the Aiyima A20. So, just trying to help you figure out what might actually be wrong in case you still want to use that amp, and if not, then all good.

By the way, I did check out their website carefully and could not find anything about the input sensitivity specifications, let alone the 2 V requirement that you cited, below is the link to their website, the info isn't that good unfortunately:


C70S simply can’t provide enough output voltage

I can see there are potentially 3 areas that you might want to double check:

1) The bypass, presumably volume control bypass, need to be press and hold for 3 seconds for it to take effect.
2) RCA gain switch, make sure it is in fact set to +3 dB. I know you said you did, but worth double checking, by say, switching it back and forth a few times and make sure you could feel that it is in fact engaged in the +3 dB position, likely indicated by a click sound/feel that you would typically get from such a selector switch.
3) The high pass filter, should set it to off, if/when you are comparing it with other amplifiers that does not have such HPF, because if it is set to on, you are going to lose the low frequency signal and the amp would not sound as loud obviously at any given input voltage level.
 
I'm thinking about using the Flex HTx as my front end / PC sound card and a Cinema 70s as a decoder in preamp only mode. It sounds like this would avoid all of these issues?
 
@peng Amir's measurements for the Cinema 70s show that it only reaches 2V RMS at a high master volume of 82.5 (and nowhere near 3.5–4V), with heavy clipping occurring if pushed further. At realistic, everyday listening levels (master volume around 50–65), the pre-out voltage is actually outputting much lower. At those real-world voltages, the Fosi's ~0.7V input sensitivity allows it to gain-match internal channels at 0 dB trim effortlessly, whereas the A20 required a +7 dB boost on the AVR. That’s why the Fosi is practically a better match for the C70S in this setup.
 
@peng Amir's measurements for the Cinema 70s show that it only reaches 2V RMS at a high master volume of 82.5 (and nowhere near 3.5–4V), with heavy clipping occurring if pushed further. At realistic, everyday listening levels (master volume around 50–65), the pre-out voltage is actually outputting much lower. At those real-world voltages, the Fosi's ~0.7V input sensitivity allows it to gain-match internal channels at 0 dB trim effortlessly, whereas the A20 required a +7 dB boost on the AVR. That’s why the Fosi is practically a better match for the C70S in this setup.
That is true but it has little, almost nothing to do with your C70s, almost no AVRs, even the flagship Cinema 49, 40 or AV10 would give you more than 2 V at volume 82.5.

If you need more than 2 V you need to crank it up further, or increase the input signal, that you can do with analog inputs.

Sorry to say this, but no offense, you seem to have some misconceptions on gain, input sensitivity. For example, I don’t know which Fosi amp you have, but if you have an older version, it might have gain as high as 29 dB or higher, not 100% sure, have to check,when set to high, while the latest version would have gain a few dB lower, but it does not mean the one with lower gain is a problem and it does not mean your Fosi is a better match just because the trim happens to be at 0. In fact if your Fosi happens to have gain as high as 32 dB, it would have higher noise, on all else being equal basis.

Which Fosi model do you have, and what year?
 
Last edited:
I am using the Fosi Audio ZA3 (with upgraded TI OPA1656 op-amps). The ZA3 has a standard 26-28 dB gain on RCA and it's not one of the older models with 32 dB gain, and with the OPA1656, noise floor is as low as possible.

My point isn't that 0 dB trim makes an amp magically 'better' in isolation, but that in an AVR environment, keeping the front pre-out channel trims around 0 dB prevents digitally boosting the signal by +7 dB inside the C70S DSP before D/A conversion.

Pushing +7 dB trim on the AVR reduces digital headroom and increases the risk of digital clipping on dynamic peaks. The ZA3 gain structure simply integrates cleanly with the C70S without needing aggressive positive trim boosts.
 
I am using the Fosi Audio ZA3 (with upgraded TI OPA1656 op-amps). The ZA3 has a standard 26-28 dB gain on RCA and it's not one of the older models with 32 dB gain, and with the OPA1656, noise floor is as low as possible.

Okay then now we have some facts: based on Amir's test, the ZA3 output 5 W with 0.22 V input, so gain is about 28.75 dB.

The Aiyima A20 stereo amp, according to Amir's test, output was 5 W, 0.233 V input, gain is about 27.14 dB, Amir just mentioned bypass but based on the 27.14 gain, he most likely has the gain selector on +3, though that is just my reasonable assumption.

So I would expect on all else being equal basis, if the same channel, say front left is driven by either amp, if the trim for the ZA3 is 0, then the Aiyima would have to be almost +4, but not +7. That's the same channel, if you are comparing the same but use the two amps to drive different channels then of course, +7, or higher, or lower would be possible.

My point isn't that 0 dB trim makes an amp magically 'better' in isolation, but that in an AVR environment, keeping the front pre-out channel trims around 0 dB prevents digitally boosting the signal by +7 dB inside the C70S DSP before D/A conversion.

Sorry your point is only valid in some cases, but not always the case. For example, it the Cinema 70s ended up with +7 when the preout of the front left channel is connected to the Aiyima, and 0 when connected to the Fosi ZA3, and if at that volume setting, you are getting 105 dB maximum SPL at your seat, then you will have no headroom concern at all. If under the same conditions you are only getting 75 dB maximum, then it could be an issue.

Headroom, like higher than needed power output don't really matter if you never need it.
Pushing +7 dB trim on the AVR reduces digital headroom and increases the risk of digital clipping on dynamic peaks. The ZA3 gain structure simply integrates cleanly with the C70S without needing aggressive positive trim boosts.

As explained above it depends, not always true, so please don't look at it as something black or white. It depends on quite a few factors, such as but not limited to speaker's sensitivity, maximum SPL capability, seating distance, impedance and your listening habit such as desired maximum SPL from your seat.

For example, if you are using the C70s and the little class D amps to drive a pair of bookshelf speakers that has the manufacturer's recommended amp power of 100 W, then they are right within the capability of either the Fosi ZA3 or Aiyima A20, then in that case there is no need to worry about headroom even if the Aiyima resulted in the C70S trim set to +7, if at +7 means volume 0 results in pre out voltage of 2 V, because at that level, the Aiyima amp would be outputting 259 W into 8 ohms, or 518 W into 4 ohms, so if you crank it up to "0", you risk blowing the poor little amp, you can see that clearly right.
 
Pushing +7 dB trim on the AVR reduces digital headroom and increases the risk of digital clipping on dynamic peaks. The ZA3 gain structure simply integrates cleanly with the C70S without needing aggressive positive trim boosts.

You don't really know that, not without knowing what caused the +7 dB trim, was it set by Audyssey, or you did it manually, and how? As explained in other posts, please do not look at it as if it is something either black or white, it really depends on multiple factors. If, the +7 was set by Audyssey it typically means at volume 0, Audyssey needs to set it to +7 in order to give you 105 dB maximum at the mmp. So then the question is, do you really listen that loud, 105 dB maximum (85 dB average) is what people called reference level, that's really loud, everyone has their own comfort zone, mine is much less, probably around 90 dB max/peak, 70 dB average when I want to listen "loud" (to me), but of course ymmv. So, if you normally listen with volume at -10, the +7 trim would still bring you up to effectively volume -3, and you would still have plenty of headroom, and to emphasize this, headroom they should never have to use because even at volume -10, effectively -3 (if the trim was 0), you don't want to raise the volume. In this and I would say most use cases, the trim level is usually use to level match the SPL of the channels at the mmp, there is no need for them to be all at or near 0.
 
markic, what speakers are you using, and your seating distance, and you typical volume setting when you want to listen loud? I just want to find out if the +7 trim might actually be better in terms of getting the C70S preout closer to the 1.5 V neighborhood where it performs best.
 
I don't look at this as purely black-and-white, these are simply conclusions drawn from hands-on, real-world usage in my own room.

As a personal rule of thumb, I prefer keeping channel trims within the ±2 dB range, ideal 0dB, and I choose hardware that easily matches that criteria in my setup. To be honest, I wouldn't keep an amp in my system that forces me to push the trim all the way up to +7 dB, even if it potentially sounded slightly better than the Fosi in its stock configuration, and with the TI OPA1656 installed in the ZA3, the sound performance between them is extremely close anyway.

To answer your question. I'm running Q Acoustics 3030c front, a 3090c center, and 3010c surrounds. I typically run Audyssey initially just as a quick baseline measurement too, it does a relatively fine job calculating basic levels and speaker distances. However, I clear its settings and turn MultEQ off afterward because Audyssey is quite poor when it comes to EQ and frequency correction, and I prefer keeping the analog signal path clean.

At the end of the day, everyone has their own approach and priorities when dialing in a system. My initial point in all of this was simply to highlight under what real-world conditions the C70S pre-out delivers clean, great-sounding stereo music playback. We've dragged this discussion out quite a bit, so I won't be posting further on this topic, but I appreciate your time and the mathematical insights. Cheers!
 
@peng Amir's measurements for the Cinema 70s show that it only reaches 2V RMS at a high master volume of 82.5 (and nowhere near 3.5–4V), with heavy clipping occurring if pushed further. At realistic, everyday listening levels (master volume around 50–65), the pre-out voltage is actually outputting much lower.
So there is not issue with headroom whatsoever.
At those real-world voltages, the Fosi's ~0.7V input sensitivity allows it to gain-match internal channels at 0 dB trim effortlessly, whereas the A20 required a +7 dB boost on the AVR. That’s why the Fosi is practically a better match for the C70S in this setup.
There is no rationale for that, but if that is what you prefer then it is your preference but to say "....the Fosi is practically a better match....." does not make sense based on facts, thought the Fosi could indeed be a better match for other reasons, just not what you seem to be saying because of the difference in gain, that resulted in the +7 dB "boost".

Before I forget, here's one that Amir showed you get > 4 V from a Denon AVR, in this case AVR-X3900H but you can also take a look of the AVR-X6700H that Amir also measured its pre out up to >4 V. He does not always measured it to that level, his standard is 2 V for unbalanced output an d 4 V for balanced output. Marantz's can do the same as the design of the preamp/DAC is the same except Denon does not have HDAMs, whereas Marantz do, though not the Cinema 70S that also does not have HDAMs.

Amir, when measuring to higher than 2 V, had to crank volume up higher such as to 90.

The fact is, those AVRs can in fact output higher than 2 V, but for D+M, that is Denon or Marantz, at volume around 80 to 83, the output would be around 2 V. The point is, it is not unique to the Cinema 70S.

1791493302816.png
 
Last edited:
I don't look at this as purely black-and-white, these are simply conclusions drawn from hands-on, real-world usage in my own room.
Good to know.
As a personal rule of thumb, I prefer keeping channel trims within the ±2 dB range, ideal 0dB, and I choose hardware that easily matches that criteria in my setup. To be honest, I wouldn't keep an amp in my system that forces me to push the trim all the way up to +7 dB, even if it potentially sounded slightly better than the Fosi in its stock configuration, and with the TI OPA1656 installed in the ZA3, the sound performance between them is extremely close anyway.
I would agree that's a good goal, but in practice it is not always realistic, for example, many HT users don't have the luxury to use the same speakers for all channels, and also don't have the luxury to place them equidistance to the MMP, even if they do, it is highly unlikely you can have the same SPL at the MMP with trim setting within +/- 2 dB across all channels. If you can easily manage that, good for you.
To answer your question. I'm running Q Acoustics 3030c front, a 3090c center, and 3010c surrounds. I typically run Audyssey initially just as a quick baseline measurement too, it does a relatively fine job calculating basic levels and speaker distances. However, I clear its settings and turn MultEQ off afterward because Audyssey is quite poor when it comes to EQ and frequency correction, and I prefer keeping the analog signal path clean.
Okay thanks, I will do some calculations but not today.
At the end of the day, everyone has their own approach and priorities when dialing in a system. My initial point in all of this was simply to highlight under what real-world conditions the C70S pre-out delivers clean, great-sounding stereo music playback. We've dragged this discussion out quite a bit, so I won't be posting further on this topic, but I appreciate your time and the mathematical insights. Cheers!

Yes I hear you but to some of your points were made base on incorrect information, I felt the need to point those out. I didn't mean to counter those points in a challenging way, but simply to try and make things more facts based. If I had made any points (and I had in the past) based on incorrect information or misconception of certain terms, specs etc., I would welcome any counter points, corrections etc., so I wouldn't unintentionally misled anyone.

Opinions, personal preferences, such as your desire to want to aim for trims within +/- 2dB for all channels are obviously completely fine and should not result in debates or arguments.
 
At the end of the day, everyone has their own approach and priorities when dialing in a system. My initial point in all of this was simply to highlight under what real-world conditions the C70S pre-out delivers clean, great-sounding stereo music playback. We've dragged this discussion out quite a bit, so I won't be posting further on this topic, but I appreciate your time and the mathematical insights. Cheers!
On my part, I just want to make clear that you may not have anything to worry about your Cinema 70S doesn't have enough output for your amps including the Aiyima amp that has lower gain than the Fosi amp. So, with due respect, I simply responded to your concerns that seems misguided, not "dragged... out the discussion" as such.

Regardless, thank you for reconfirming the speakers you are using for you setup, I just want to be sure before I do my calculations to see whether the Cinema 70S and the Fosi or Aiyima amp have the voltage and power outputs. Without knowing your seating position, I am going assume 3 meters, that I think has a good chance to be at least in the ball park based on the fact that they are relatively small bookshelf type and your listening levels are in the master volume 50-65 range.

Below are the calculated/estimated result based on the info you provided and assumed distance of 3 meters from you seat:

SpeakerssensitivityDistanceImpedanceRecommended amp power
FrontQ Acoustic 3030C86.53 m690
CenterQ Acoustic 3090C91.8unknown6150
SurroundQ Acoustic 301085unknown685

Calculated results for the C70S pre out voltage:

From Amir tests, we know the pre-out voltage is 2 V with master volume at 82.5, that means at 65, the voltage will be just under 0.25 V, and with trim at +7, the actual pre out voltage would be just over 0.56 Vrms

This shows your front speakers can in fact be driven to their limits and the Cinema 70S has plenty of headroom even if you crank it up to 82.5.

Calculated results for the power amplifiers outputs:

With pre out = 0.56 V, the Aiyima A20 amp will output about 27 W, the Fosi ZA3 would output about 39 W because of its higher gain.

Amir's test results also show that the Aiyima A20 output about 180 W, 4 ohms, at 1% THD, at that output level, the C70S output would need to be about 1.45 V, and that's indeed would put the C70S in its optimal range, with SINAD slightly better than a whopping 97 dB.

That shows you absolutely have no need to be concerned about not getting "clean" output from the AVR based on your master volume 65 listening level.

So, to conclude this lengthy discussion, the +7 dB trim you ended up with, when using the Aiyima amp is not because of the C70S pre out voltage limit, not because of the Aiyima's relatively low gain, actually only relative to the Fosi ZA3, because with the selector set to +3, the A20's gain is a little higher than 27 dB, that is not low at all, the popular Hypex based amps have gains in the range of 25 to 16 dB typically. The reason for the +7 is mainly due to the relatively (relative to the Center speaker, the 3090D low sensitivity of the Q Acoustics 3030C.

Even if we assume the 3030C and the 3030C are equidistance to your seat, there is a significant difference of 5.3 dB in their sensitivity specs, so if the trim for the center channel is 0, it would be +5.3 for the front channels, again that's only based on equidistance and no room gain, so in reality, the +7 difference would seem highly realistic.

Last point, or just friendly reminder, have you checked and make your Aiyima amp's high pass filter is/was set to OFF? From the website pictures, it seems that the amp might come with the filter set to 80 Hz, that would be at least partly the reason for the seemingly higher trim set by the AVR.

I understood you wouldn't post further on this topic, but just would like you to know you are welcome to question any of my calculated/estimated results and I'd try my best to explain how they were done.

And, if you are interested, for those who don't know the formula involved, one does not need to be an EE, because the following website has just about all the necessary formula, even some calculators:

 
I really appreciate the time and effort you put into all these detailed calculations, peng!

You're spot on regarding the sensitivity difference between the 3030c and the center 3090c, that explains a lot from a purely mathematical standpoint. And just to clear that up: no, the HPF on the A20 wasn't engaged, but since I'm fully committed to the Fosi ZA3 setup now, that's water under the bridge anyway.

It’s great to see on paper that the C70S has more than enough voltage headroom under these conditions. My preference for keeping trims near 0 dB is simply a personal workflow rule for peace of mind in my analog signal chain, but your math makes total sense for the system as a whole.

Thanks again for the valuable breakdown!
 
I really appreciate the time and effort you put into all these detailed calculations, peng!

You're spot on regarding the sensitivity difference between the 3030c and the center 3090c, that explains a lot from a purely mathematical standpoint. And just to clear that up: no, the HPF on the A20 wasn't engaged, but since I'm fully committed to the Fosi ZA3 setup now, that's water under the bridge anyway.

It’s great to see on paper that the C70S has more than enough voltage headroom under these conditions. My preference for keeping trims near 0 dB is simply a personal workflow rule for peace of mind in my analog signal chain, but your math makes total sense for the system as a whole.

Thanks again for the valuable breakdown!

Thank you, I am amazed the Cinema 70S measured so well on Amir's test bench. At one point I considered using it as preamp/pro for one of my stereo system but I wanted two discrete sub outs for use with DLBC (Dira) PC version so had to give up on that idea. You have some nice speakers that have decent bass extension but may do even better with a good subwoofer. Time to focus on enjoying the music right!
 
Thank you, I am amazed the Cinema 70S measured so well on Amir's test bench. At one point I considered using it as preamp/pro for one of my stereo system but I wanted two discrete sub outs for use with DLBC (Dira) PC version so had to give up on that idea. You have some nice speakers that have decent bass extension but may do even better with a good subwoofer. Time to focus on enjoying the music right!
I wonder if the series 2 will do better. Dirac is tempting for me, should be better than the simple Audyssey. Sitting with the NR1710 and really want these slim line models.
 
I wonder if the series 2 will do better. Dirac is tempting for me, should be better than the simple Audyssey. Sitting with the NR1710 and really want these slim line models.
On paper it will be better because of the Cirrus Logic DAC IC but it may not make any difference audibly especially if you use the build in power amps.
 
On paper it will be better because of the Cirrus Logic DAC IC but it may not make any difference audibly especially if you use the build in power amps.
Mostly a bit dissapointed by the very slow filter of previous versions. Was thinking of the 70S and now prices are falling. But if better DAC and Dirac of series 2 well perhaps that is the one for me. Expensive yes but there is no other small unit like this. Two small power amps for main speakers is on the way as well.
 
Back
Top Bottom