• Welcome to ASR. There are many reviews of audio hardware and expert members to help answer your questions. Click here to have your audio equipment measured for free!

making a phono connector cable. Got some wire questions.

David James

Member
Joined
Feb 6, 2021
Messages
46
Likes
65
I have a vintage thorens, and acquired a Jelco Profile ii tonearm. I want to try a AT vm740xml cartidge. Tonearm comes without a cable so I have to come up with one. There are a few specific technical requirments:

- Thorens is suspended. To not impede the sensitive spring suspension the cable needs to be very flexible.

- The tonearm requires a right angle DIN connector, with pins rotated to 260 degrees.

- Audio Technica state that VM740xml is sensitive to capacitance and will be bright if its too high.

Looking for suggestions for flexible cable with low capacitance. I'm sure Audio isn't the only field where this is required, and I'm willing to bet what might cost me $100 from an audio company will cost significantly less from almost any other.

I have a few options for the DIN connector, but it is from Cardas and therefore pricey. Has anyone come across an amazon or ebay solution that isn't at audiophile pricing?

I am in Canada.
 
Last edited:
Zavfino's connectors are well thought of and not too expensive, at least compared to some other "high end" brands. There should be other options too, though could depend on where you're located. Tonearm cables in general are a lot more expensive than your regular RCA cables (since demand is low, I guess), so it's a good idea to make your own.
 
Are you looking for components to make your own, or a ready made one?
 
I like making cables, but I'm open to either option. I'm averse to the often unreasonable pricing of audiophile products, but if there was a reasonably priced prefab option I'd consider it.
 
Zavfino's connectors are well thought of and not too expensive, at least compared to some other "high end" brands. There should be other options too, though could depend on where you're located. Tonearm cables in general are a lot more expensive than your regular RCA cables (since demand is low, I guess), so it's a good idea to make your own.
Thanks for the suggestion. This is way outside of what I'd pay for cables though.
 
The 5-pin connector is kind of specialized, so it tends to be a bit expensive, but sub-30 USD seems to be the norm on *Bay and Aliexpress. I found the following item on *Bay. As supplied, it doesn't appear to allow the rotation angle to be changed, but if you're willing to drill an additional hole in the outer shell, you ought to be able to position it at any angle you like.
tonearm connector.jpg
 
I've been eyeing those. I assumed the screw on the top allowed the plug to be pulled out and rotated but the ebay/amazon ones never tell you if that the case or not.

Having said that, I think I might have a solution that would side step the need.

Stock, the 32awg tonearm wires exit the column and mount to a terminal block. The interconnect cable runs from the terminal block to the Phono pre. Random internet source states capacitance of the stock interconnect is around 95pf/meter.

Rather than constructing a cable that might mess with the suspension, I think I will get a din plug, without the housing, solder 32awg to the terminal, and then shorten the existing interconnect, since its rather long.

I am planning to build a new plinth, and haven't grappled with the question of whether to have RCA connectors on the rear of the plinth or not. It would allow me to change the cables as needed. I do have some amps with built in phono stages so I might need to go back to longer connectors if I want to use those again, assuming I'm changing cartridges and can afford the capacitance cost of longer runs.
 
I'm in Canada.

This is the sort of thing I was looking for. Thanks. Quick search suggests we don't pay duty on cables from UK, so if shipping is reasonable this might be a solution.
 
Back
Top Bottom