• Welcome to ASR. There are many reviews of audio hardware and expert members to help answer your questions. Click here to have your audio equipment measured for free!

Genelec Owners Lounge and Discussion

Erin on GLM in an upcoming review

"Then there is GLM. Incredibly easy to use. Great results in literal minutes. It smoothed out the bass response on its own and then I took some additional time to sit with my laptop in my lap, while listening to the speakers and tweaking the EQ in real-time to get a more subjectively-preferred tonal balance. Initially the HF was a bit too flat in-room so I used a couple shelf filters - one on the bass and one on the treble - and landed on a very neutral balance that I could listen to for hours. I've attached a screenshot of the GLM software showing the measured vs calibrated response as well as my personal tweaks ("Low Shelf 1+" and "High Shelf 1+"). Note that I used the asymmetrical EQ option because my room isn't symmetrical; there is a partially open hallway on the left and a full sidewall on the right."
 
Erin on GLM in an upcoming review

"Then there is GLM. Incredibly easy to use. Great results in literal minutes. It smoothed out the bass response on its own and then I took some additional time to sit with my laptop in my lap, while listening to the speakers and tweaking the EQ in real-time to get a more subjectively-preferred tonal balance. Initially the HF was a bit too flat in-room so I used a couple shelf filters - one on the bass and one on the treble - and landed on a very neutral balance that I could listen to for hours. I've attached a screenshot of the GLM software showing the measured vs calibrated response as well as my personal tweaks ("Low Shelf 1+" and "High Shelf 1+"). Note that I used the asymmetrical EQ option because my room isn't symmetrical; there is a partially open hallway on the left and a full sidewall on the right."

So you've publicly shared part of his written review that's currently only available on his Patreon? Did you ask him first?
 
Hi, I've been looking at picking up a used/pre-owned pair of Genelec 80X0 series. The cosmetic condition is not ideal with many scratches, nicks, dings, etc.
Has anyone managed to restore the physical appearance of these aluminum speakers before? With the producer grey finish this usually isn't too big of a problem. But i did find some black ones and boy do they look rough.
 
Erin on GLM in an upcoming review

"Then there is GLM. Incredibly easy to use. Great results in literal minutes. It smoothed out the bass response on its own and then I took some additional time to sit with my laptop in my lap, while listening to the speakers and tweaking the EQ in real-time to get a more subjectively-preferred tonal balance. Initially the HF was a bit too flat in-room so I used a couple shelf filters - one on the bass and one on the treble - and landed on a very neutral balance that I could listen to for hours. I've attached a screenshot of the GLM software showing the measured vs calibrated response as well as my personal tweaks ("Low Shelf 1+" and "High Shelf 1+"). Note that I used the asymmetrical EQ option because my room isn't symmetrical; there is a partially open hallway on the left and a full sidewall on the right."
 
I have setup a 4.0 system with 8340 as mains and 8010 as surrounds. The idea is to upgrade surrounds to 8320 to benefit from GLM.

Ideally I would connect 8340 via digital input and 8320 analog (obviously). Is it possible to group like that in GLM? AI says no, but this seems too specific for it.
 
I have setup a 4.0 system with 8340 as mains and 8010 as surrounds. The idea is to upgrade surrounds to 8320 to benefit from GLM.

Ideally I would connect 8340 via digital input and 8320 analog (obviously). Is it possible to group like that in GLM? AI says no, but this seems too specific for it.
Why do the 8320 have to be analogue? Why not connect them digitally as well? Oh wait, I vaguely recall the smaller SAM monitors don't have digital input...
 
Why do the 8320 have to be analogue? Why not connect them digitally as well? Oh wait, I vaguely recall the smaller SAM monitors don't have digital input...
Yes, the 8320 is the only SAM monitor with no digital input.

But my plan did not work, so will have to remain in the analog domain.
 
 
I managed to go all digital connections with my 8331A monitors and 7350A subwoofer using an SMSL PO100, Neutrik Impedance Transformer and the relevant cables. I'm controlling the volume using a 9310B controller connected to the GLM network adapter.

Is it normal to hear relay switching sounds when powering on the speakers from GLM? I never heard switching before with the analog connections.
 
I managed to go all digital connections with my 8331A monitors and 7350A subwoofer using an SMSL PO100, Neutrik Impedance Transformer and the relevant cables. I'm controlling the volume using a 9310B controller connected to the GLM network adapter.

Is it normal to hear relay switching sounds when powering on the speakers from GLM? I never heard switching before with the analog connections.

I hear a sound when I power on the speakers from GLM, and it's the same sound when they are woken up by a musical signal. It's a very quiet "tick" sound. I hear it when the turn off too. It's not a conventional relay "click" but that could be because the aluminum enclosure is mostly muting the sound.
 
A possibly dumb question for the Genelec hive mind:

Whenever I see photos of W371s - from Genelec Experience Centers, from professional studios, wherever - the W731s' placement always makes them into speaker stands for the SAM monitors they're paired with.

Screenshot 2026-10-27 at 3.24.29 PM.png


This of course is the best aesthetic solution - the W371s could look rather strange, and in many spaces quite ugly and intrusive, if they weren't placed directly beneath the monitors. And acoustically I also understand why they're placed like that: the W371s' frequency range goes at least a couple octaves up into the range where frequencies are clearly and easily localizable by the human ear, so they can't be placed at visually random locations like one can do with a conventional subwoofer.

But given that limitation in where the W371s can be placed, it would then also seem that you can't necessarily deal with room-induced bass nulls or similar issues by experimenting with a lot of different placement locations and arrangements like you can with a pair of conventional subs.

So is the idea that the W371s' special dual-driver arrangement and DSP enables them to produce smooth response by controlling directivity and other aspects? Or is it that their improvement in the ≈100-400Hz range not covered by subs is so dramatic that it outweighs any low-bass nulls that their placement limitations might prevent you from fully addressing?

Again, apologies in advance if this is a hopelessly dumb question. But I'd rather look dumb and learn something than say nothing and remain confused.

Thanks!
 
Last edited:
Back
Top Bottom