• Welcome to ASR. There are many reviews of audio hardware and expert members to help answer your questions. Click here to have your audio equipment measured for free!

Fosi BT20A Max Amplifier Review

Rate this amplifier:

  • 1. Poor (headless panther)

    Votes: 2 1.3%
  • 2. Not terrible (postman panther)

    Votes: 33 20.8%
  • 3. Fine (happy panther)

    Votes: 107 67.3%
  • 4. Great (golfing panther)

    Votes: 17 10.7%

  • Total voters
    159
Which subwoofer plays clean bass?
EDIT: clean bass. significantly less distorted and lower bass when played at volume.

I'm thinking of a typical bookshelf system with 5.25" woofers paired with a 12" subwoofer and played at volume.

While I agree that small subwoofers often disappoint. Do you agree with the point I was trying to make? That is, if an amplifier manufacturer is going to include a subwoofer output, then it has to also include a HPF.

After all, if someone feels the need to add a subwoofer, then they are probably not happy with the bass that their main speakers are outputting - at least at the volumes that they listen to.
 
Note also the nice inclusion of a tone bypass switch on the back, theoretically at least removing or reducing the effect of having tone controls on the FR linearity.
 
Power 8 ohm ?
Oops. Added to the review:

index.php
 
Great review as always!!!

A just ok implementation.
PFFB not so nicely executed . Maybe the tone controls have something to do with these SINAD numbers.
A missed opportunity IMHO...
 
Thanks for the great review, Amir. The thing that occurs to me is that since all these integrated chip amps have volume controls (this one especially, since it has a motorized volume knob), there is no need to pay for a DAC which also has a volume knob. There have been a few DACS with near perfect performance numbers that have no volume knobs going for $80 or less, making them a perfect pairing with the B20a. Just run a USB cable from your PC to the DAC, a couple of RCA cables, and you're probably meeting two channel electronics needs for l.t. $350. And there are any number of excellent near full range speakers from KEF, ASCI, Ascend, and even Warfedale for $1000-1600.
 
Great review as always!!!

A just ok implementation.
PFFB not so nicely executed . Maybe the tone controls have something to do with these SINAD numbers.
A missed opportunity IMHO...

Pretty typical PFFB implentation on this tier of product. The V3 Mono and 3E audio achieve better results than this, but it's marginal. Notice the response curve is about the same with 4 and 8 ohm loads with 1dB or less variance in the audible band, which basically amounts to inaudible in real world. If someone can hear less than .5dB rise at 15kHz, I want to shake their hand.
 
I am eagerly awaiting the ASR review of the new FiiO AIR AMP PFFB streaming amplifier, based on the TPA3255 chip and priced at €249 that combines a streamer, a DAC and Class D stereo amplification. Paired with the supplied power supply, it delivers up to 2×120W into 4Ω and supports PCM streams up to 32bits 768kHz as well as DSD512 + PEQ eq....
 
When I saw Fosi in the review title, my expectations went up. Fosi seems to be on their game and my experience with Fosi - I have a Fosi V3 - has been positive.

Good job, Fosi!

In my opinion, this will be the last TPA3255-based amplifier from Fosi. They are now shifting toward Hypex for the V4 and V5—but at what price...

Fosi V4 Mono
- Hypex 250 watts (Ncx250mp ? )
- Front LED
- Build-in PSU, most likely built-in PSU amplifier module
- approx $500 - 600

Fosi V5 Mono
- Hypex 550 watts (Ncx500mp ? )
- Touch display
- Most likely a remote
- Dedicated power supply for amplifier
- Dedicated power supply for other electronics like display etc.
- approx $1000
 
In my opinion, this will be the last TPA3255-based amplifier from Fosi. They are now shifting toward Hypex for the V4 and V5—but at what price...

Fosi V4 Mono
- Hypex 250 watts (Ncx250mp ? )
- Front LED
- Build-in PSU, most likely built-in PSU amplifier module
- approx $500 - 600

Fosi V5 Mono
- Hypex 550 watts (Ncx500mp ? )
- Touch display
- Most likely a remote
- Dedicated power supply for amplifier
- Dedicated power supply for other electronics like display etc.
- approx $1000
Probably not, this is also coming
1792664044413.png

1792664196240.png

I think Fosi will continue to flood the market with many many products hoping for a big seller
 
Boost over 10k plus not so great HF IMD makes me worried about shrillness at high volume, so Fine, not Great. What do the tone controls do? What is the FR of the sub out and does it then high-pass the mains? These to me seem critical to include in a review.
 
Because there are very few cheap amps with a sub out and an HPF filter, and should be more. Adding sub with proper HPF very useful for upgrading almost any speakers. Too bad there is BT but no USB input.
Yes, if it had a few more features, (even if it cost $300), it would be a worthwhile Christmas gift to someone to start them into stereo.
 
Would BT20a max survive standard FTC amplifier tests?


Standardized Testing Conditions: If a manufacturer chooses to advertise power output, the measurement must use a load impedance of 8 ohms, cover the full frequency band of 20 Hz to 20 kHz, and keep total harmonic distortion plus noise (THD+N) at or below 1.0%.

Continuous Power Duration: The input signal must run continuously at full rated power for at least 5 minutes prior to or during measurement.

Preconditioning: Testing requires a preconditioning period of 1 hour at 1/8th power into an 8-ohm load (for general power disclosures).

 
Pretty typical PFFB implentation on this tier of product. The V3 Mono and 3E audio achieve better results than this, but it's marginal. Notice the response curve is about the same with 4 and 8 ohm loads with 1dB or less variance in the audible band, which basically amounts to inaudible in real world. If someone can hear less than .5dB rise at 15kHz, I want to shake their hand.
You can shake their hand while I steal their ears…
Great review per usual Amir!
My opinion? A lot to choose from around this price point and I’m not so sure the BT20A rises significantly above the rest.
….But it sure is a looker.
 
Is it fair to rate these based on SINAD at 1khz & 5w given the distortion rises (sometimes massively) as frequency and power rise? 5w for an 86db sensitive speaker at 10' listening distance is pretty quiet.

For example, both this amp and the Yamaha are at 91 in the rankings, but the power vs distortion numbers are markedly different. Yamaha's spec is THD at 20hz-20khz @ 50w. Maybe looking at 20khz is too high, but I thought our ears were most sensitive to distortion in the 1-5khz range. Apologies if this has already been beaten to death.

index.php


index.php
 
Is it fair to rate these based on SINAD at 1khz & 5w given the distortion rises (sometimes massively) as frequency and power rise? 5w for an 86db sensitive speaker at 10' listening distance is pretty quiet.
I don't what is "fair." But high frequency energy in music is far lower than what you see in my full power sweeps. As a result, distortion that is generated will be at far lower level. Further, the harmonics of high frequencies land outside of our hearing range and capability of the speaker to produce them.

So while from engineering excellence point of view it would be nice to have frequency independent results -- or at least more linearity -- it is less of a concern than it seems.

There may be some call for doing the opposite: measuring SINAD at low enough frequency that its harmonics won't be masked. This would be in upper bass region.
 
Would a 48V really help this device? 24V is good enough and 32V is more than enough.
 
Back
Top Bottom