Buckeye Amps: 2nd Generation Purifi EIGENTAKT 1ET9040BA Amplifier

[Buckeye Amps]

Announcing our new Purifi 2nd generation EIGENTAKT 1ET9040BA Monoblock amplifier!

Purifi 1ET9040BA Power Specs (1kHz, THD = 0.1%):
- 375w @ 8ohm (peak)
- 750w @ 4ohm (peak)
- 1400w @ 2ohm (peak)

40A output current

Custom Input Board:

• Neutrik XLR connectors
• Gold plated 5-way speaker binding posts
• OPA1656 Input Stage
• TI TPS7A30/49 Voltage Regulators
• Clipping Indication (via front power LED)
• Error Indication (via front power LED)
• Auto Sensing On/Off (along with Always On and 12v Trigger)

Variable Gain Settings:
4 ohm - 25.5dB/2.9Vrms (High), 20.5dB/5.2Vrms (Medium), 15.5dB/9.2Vrms (Low)
8 ohm - 25.5dB/2.9Vrms (High), 20.5dB/5.2Vrms (Medium), 15.5dB/9.2Vrms (Low)

Case dimensions are 10" W x 13" D x 3.5" H

Email directly ([email protected]) for buying or if you have any questions at all

Visit our website for up to date specs, pricing, and pictures:
Buckeye Amps Official Site

 

[MGJ]

So much power and it will probably weigh less than 10lbs.

 

[jruser]

are the gain options going to match your other amps?

 

[Buckeye Amps]

are the gain options going to match your other amps?

Very closely yes

 

[tmtomh]

Goodness - so much clean power for less than $1300, the size of a stack of about 15 LPs. Crazy.

 

[Madcow]

I’m down I got some jbls rated at 1500 watts and right now I’m running the gan1 which sounds pretty amazing already. But I might want to bump up the powah!

 

[shion_ca]

Is there an option to leave the amps idle-ing in a warm state? What does the auto on/off do?

Evan you remind us of the configurable gain options?

 

[NTK]

What does the auto on/off do?

So it can be legally sold in the EU.

Standby, networked standby and Off mode

Off mode, standby and networked standby mode. Energy efficiency of products.

energy-efficient-products.ec.europa.eu

 

[shion_ca]

Can it be defeated?

 

[Buckeye Amps]

Auto On/Off turns the amp on automatically when a signal is detected over the Ch1 input and turns off when the signal level drops below a threshold for more than ten minutes.
It is user selectable.

Otherwise the amp can be left on indefinitely or a 12v trigger cable can also be used

 

[Buckeye Amps]

So yes, you can leave the amp in an idle mode if you'd like when not using it but I would not advise since it will waste power for no reason.

 

[pogo]

Will there also be a bi-wiring version (see also datasheet para. 2.3.2)?
Is the modification (blue wire) also available in the series?

 

[Buckeye Amps]

Will there also be a bi-wiring version (see also datasheet para. 2.3.2)?
Is the modification (blue wire) also available in the series?

The blue wire is there as this is one of our prototype boards.

Can also probably add bi wiring ability though not really necessary

 

[pogo]

It is necessary with bi-wiring capable speakers for maximum performance, see also data sheet.

 

[Buckeye Amps]

It is necessary with bi-wiring capable speakers for maximum performance, see also data sheet.

I've seen the data sheet, yes

 

[shion_ca]

Can you share the selectable gain levels?

 

[Buckeye Amps]

Some good news:

Since we decided to make the input board for the Purifi 9040BA a standalone board (and not make it an all purpose board that supports all other mono builds we offer) we have switched the OP amp to the TI OPA1656.

 

[Doodski]

Some good news:

Since we decided to make the input board for the Purifi 9040BA a standalone board (and not make it an all purpose board that supports all other mono builds we offer) we have switched the OP amp to the TI OPA1656.

What features and benefits does this OP amp provide?

 

[Buckeye Amps]

What features and benefits does this OP amp provide?

When compared to the OPA1612, nothing audible. It is mainly a switch to be more in line with what Bruno recommends and what the community expects.

If measuring, one advantage of the 1656 over the 1612 is higher impedance.

 

[amper42]

When compared to the OPA1612, nothing audible. It is mainly a switch to be more in line with what Bruno recommends and what the community expects.

If measuring, one advantage of the 1656 over the 1612 is higher impedance.

Another feature is the OPA1656 is less than half the cost of the 1612.