• WANTED: Happy members who like to discuss audio and other topics related to our interest. Desire to learn and share knowledge of science required. There are many reviews of audio hardware and expert members to help answer your questions. Click here to have your audio equipment measured for free!

Bose 901 Series V Speaker Review!

hardisj

Major Contributor
Reviewer
Joined
Jul 18, 2019
Messages
2,907
Likes
13,908
Location
North Alabama
It is done! I completed the Bose 901 Series V speaker review and have posted it to my website. I am copying/pasting the majority of it here but go to the site if you want to read everything (or if links don't work here, etc).
https://www.erinsaudiocorner.com/loudspeakers/bose_901_series_v/
I'm proud of this one. Lots of work and time went in to creating this. About 20 hours so far. But I learned a lot and hopefully others will, too.

This speaker is definitely getting a YouTube review. There's no way to go through everything I want to say without spending several more hours.



Bose 901 Series V Speaker Review
  • Wednesday, Jul 22, 2020
DSC06316_resized.png

Intro
A few things that need to be stated up front before people skip this and go to the pictures:
  1. Pay attention to the Title of each graph. This speaker comes with an EQ that has all sorts of various slider positions. I tested the speaker “Raw” (without the EQ in-line) first. Then I tested it with the EQ in-line, with a few different setting configurations. There is a lot to unpack here. The title of each graph tells you how the settings were made. Please pay attention to the titles; otherwise you will get confused as to what is going on.
  2. Some may be concerned that this “Spinorama” data doesn’t take in to affect the speakers needing to be close to a surface. I have attached an image below but to summarize: The speakers should be placed at least 18 inches from side walls (with a recommendation of 2-4 feet from side walls) and 8-16 inches from the rear wall. The “Spinorama” data does not take this into account. And, at this point, I do not know how to manipulate the data in a way to “trick” the Spinorama graphics in to showing what would happen when you place them in the manner they were designed to be placed. Although, one can make the case that the SPL is simply adjusted by +6dB for this proximity and transition from the standard 4-pi reference to a 2-pi reference (free space vs near-wall). That’s just the reality. So, before anyone gets up in arms about this factor; yes, I am fully aware of the potential limitation related to this speaker’s direct/reflective design.
  3. The EQ was always in-line in my listening sessions.
901%20V%20Manaul%20Page%204.png


901%20V%20Manaul%20Page%205.png


Moving on…
The Bose 901 has been around for 50+ years and has long been considered a divisive product within the audiophile community. I was born in 1982 and until this week I had never heard the Bose 901 speakers. I’d just heard about them. Everything we all have heard and read. The same old clichés. Some love them. Some love the nostalgia of them. Some despise them and everything they represent; from the company to the product performance and how it colors (no pun intended) listeners’ perception of what good sound is supposed to be.
There have been some who have provided measurements of these speakers (NoAudiophile did here). However, there are no measurements that replicate anechoic data. Additionally, with the gaining popularity of the CEA/CTA-2034 method of providing a complete set of measurements and a prediction for in-room performance based on Floyd Toole’s work, I couldn’t stop wondering not only how the 901 would sound to me but also how they would fare in the CTA-2034 standard set of curves. Long story short, a fellow forum member of AudioScienceReview was kind enough to send me his pair of Bose 901 Series V speakers. Funny side story: he was going to send the Series IV he owned but had issues when it came time to refoam them so he sourced a very good condition pair of Series V’s and shipped them to me. Given the Series VI is the last production model and that the Series V and IV (apparently) only differ in cosmetic fashion, I was happy to have the “latest” 901 version to test.
This version consists of a single “full range” 4.5 inch driver up front and 8… yes, 8… 4.5 full range drivers in the back. The idea is to place these near a rear-wall and the 8 speakers in the back would create an enveloping sound. Well, they certainly do that. But, as you can imagine, they are not what I would consider accurate or reference speakers. Still, they’re novel and I rather enjoy the novelty. I get why people hate them. I also understand why people love them. If I had endless money and space, I’d love to have these in a dedicated room as an alternative to a reference system. Something to go in to, plop down in a big comfy chair and just kick back and enjoy these for what they are: a novelty speaker that does bring a grin to my face.
I’ll get back to my subjective thoughts later but for now let’s move on to the data.
Foreword: Subjective Analysis vs Objective Data (click for more)


Product Specs and Photos
DSC06316.JPG

DSC06318.JPG

DSC06326.JPG

DSC06325.JPG

DSC06330.JPG


Objective Data
Before I dive into the test, let me reiterate the fact this speaker has a multitude of EQ options. I tested the speaker “raw”, primarily. I also tested with the EQ in-line varying the settings. So, again, please read the title of each graphic because these tell you what was measured in that particular instance.
When the graph says “No EQ” that means there was No EQ In-Line for the measurement. In other words, this is a raw speaker measurement.



Unless otherwise noted, all the data below was captured using Klippel Distortion Analyzer 2 and Klippel modules (TRF, DIS, LPM, ISC to name a few). Most of the data was exported to a text file and then graphed using my own MATLAB scripts in order to present the data in a specific way I prefer. However, some is given using Klippel’s graphing.


EQ Box Testing
I used Klippel’s Distortion Analyzer 2 to capture the Bose 901 Series V’s various EQ settings. As you can see from the above photo of the EQ box there are various slider positions for “Mid Bass” and “Mid Treble”. There is also a “Bass” setting which accentuates the lower bass. I have provided two graphics below showing 1) difference between “Bass 1” and “Bass 2” (when EQ is set to the Neutral position) and 2) the comparison of the MidBass and MidTreble sliders (with Bass = 2).
As you can see below, the “Bass” button boosts the LF response another 5dB or so.
Bose%20901%20Series%20V%20Equalizer%20Settings%20Bass1%20vs%20Bass2.png


These are a sampling of the various EQ slider positions, where Bass = 2. The yellow line is the “EQ Neutral” setting; meaning the EQ sliders were at the middle detent … I also refer to this as “flat”, even though it’s not electrically flat… it’s just the default setting. As you can see, there is a lot of swing available on both ends and the 1kHz region is the closest to the same any of these settings comes to.
Bose%20901%20Series%20V%20Equalizer%20Settings.png




Impedance Phase and Magnitude
Impedance measurements are provided both at 0.10 volts RMS and 2.83 volts RMS. The low-level voltage version is standard because it ensures the speaker/driver is in linear operating range. The higher voltage is to see what happens when the output voltage is increased to the 2.83vRMS speaker sensitivity test. I did measure with the EQ in-line but there was no meaningful difference so I won’t bother sharing the results.
Bose%20901%20Series%20V%20(No%20EQ)_Impedance_0.1v_&_2.83v.png


Bose%20901%20Series%20V%20(No%20EQ)_FR_vs_Impedance_2.83v.png


From the above data we can see the following:
  • The tuning frequency is in the low 30’s.
  • Lots of little resonances; namely the minor dip at 650Hz followed by the peak/dip at ~1kHz. Then another around 2.5kHz.
  • Yes, the scale of the Phase is crazy; that’s a real measurement and I don’t know what’s going on to cause such a wild shift here. So I am leaving it.


Frequency Response

Notes about measurements (click for info)
The measurement below provides the frequency response at the reference measurement axis - also known as the 0-degree axis or “on axis” plane - in this measurement condition was situated at the ribbon.
Bose%20901%20Series%20V%20(No%20EQ)%20FR_Linearity.png


The mean SPL without EQ in-line is approximately 81dB at 2.83v/1m, calculated over the frequency range of 300Hz to 3,000Hz.
The blue shaded area represents the ±3dB response window from my calculated mean SPL value. As you can see in the blue window above, the Bose 901 Series V sans EQ has a ±3dB response from 62Hz - 20kHz. The ±1.5dB window is even worse. But, it’s a single 4.5” woofer with an off-shaped (by modern standards) baffle. Not making excuses. Just saying.
Now let’s look at a couple other measurements with the EQ in-line. Again, the title tells the EQ setup.
Bose%20901%20Series%20V%20(Bass%202%20-%20EQs%20Neutral)%20FR_Linearity.png


Bose%20901%20Series%20V%20(Bass%202%20-%20Treble%20Min,%20Midbass%20Flat)%20FR_Linearity.png


Below are both the horizontal and vertical response over a limited window (90° horizontal, ±40° vertical). I have provided a “normalized” set of data as well. The normalization simply means that I took the difference of the on-axis response and compared the other axes’ measurements to the on-axis response which gives the viewer a good idea of the speaker performance, relative to the on-axis response, as you move off-axis.
Bose%20901%20Series%20V%20(No%20EQ)%20Horizontal%20FR.png


Bose%20901%20Series%20V%20(No%20EQ)_Horizontal_FR_Normalized.png


Bose%20901%20Series%20V%20(No%20EQ)%20Vertical%20FR.png


Bose%20901%20Series%20V%20(No%20EQ)%20Vertical%20FR%20Normalized.png


As I said above, the provided frequency response graphs were given with a limited set of data. I measured the response of the speaker’s vertical and horizontal axis in 10-degree steps over 360-degrees. Nearly 70 measurements in total are represented in my data. As you can imagine, providing all those data points in a single FR-type graphic below is a bit overwhelming and confusing for the viewer. A spectrogram is an alternate way to view this full set of data. This takes a 360-degree set of data and “collapses” it down to a rectangular representation of the various angles’ SPL. I have provided two sets of data: one set for horizontal and one for vertical. Each set consists of 2 graphics:
  1. Full response (20Hz - 20kHz with the angles from 0° to ±180°) with absolute SPL values
  2. Full, “normalized” response (20Hz - 20kHz with the angles from 0° to ±180°) with SPL values relative to the 0-degree axis
Normalized plots make it easier to compare how the speaker’s off-axis response behaves relative to the on-axis response curve.

Bose%20901%20Series%20V%20(No%20EQ)_Horizontal_Spectrogram_Full.png


Bose%20901%20Series%20V%20(No%20EQ)_Horizontal_Spectrogram__Norm_Full.png


Bose%20901%20Series%20V%20(No%20EQ)_Vertical_Spectrogram_Full.png


Bose%20901%20Series%20V%20(No%20EQ)_Vertical_Spectrogram_Norm_Full.png



The above spectrograms are the standard way of providing directivity graphics by most reviewers. Some prefer not to normalize the data. Some prefer to normalize the data. Either way, it’s a useful visual to get an idea of the directivity characteristics of a speaker or driver.
However, these “collapsed” representations of the sound field are not very intuitively viewed. At least not to me. So, I came up with a different way to view the speaker’s horizontal and vertical sound field by providing it across a 360° range in a globe plot below. I have provided both an absolute SPL version as well as a normalized version of both the horizontal and vertical sound fields.
Note the legend provided in the top left of each image which helps you understand speaker orientation provided in my global plots below.
Bose%20901%20Series%20V%20(No%20EQ)_360_Horizontal_Polar.png


Bose%20901%20Series%20V%20(No%20EQ)_360_Horizontal_Polar_Normalized.png


Bose%20901%20Series%20V%20(No%20EQ)_360_Vertical_Polar.png


Bose%20901%20Series%20V%20(No%20EQ)_360_Vertical_Polar_Normalized.png




Now let’s look at a couple other measurements with the EQ in-line. Again, the title tells the EQ setup.
This is with the EQ in-line but set to neutral (middle detent).
Bose%20901%20Series%20V%20(Bass%202%20-%20EQs%20Neutral)_Horizontal_Spectrogram_Full.png


Bose%20901%20Series%20V%20(Bass%202%20-%20EQs%20Neutral)_Vertical_Spectrogram_Full.png


Bose%20901%20Series%20V%20(Bass%202%20-%20EQs%20Neutral)_360_Horizontal_Polar.png


Bose%20901%20Series%20V%20(Bass%202%20-%20EQs%20Neutral)_360_Vertical_Polar.png




This is with the EQ in-line with the MidBass set to Neutral and the MidTreble set to max.
Bose%20901%20Series%20V%20(Bass%202%20-%20Treble%20Min,%20Midbass%20Flat)_Horizontal_Spectrogram_Full.png


Bose%20901%20Series%20V%20(Bass%202%20-%20Treble%20Min,%20Midbass%20Flat)_Vertical_Spectrogram_Full.png


Bose%20901%20Series%20V%20(Bass%202%20-%20Treble%20Min,%20Midbass%20Flat)_360_Horizontal_Polar.png


Bose%20901%20Series%20V%20(Bass%202%20-%20Treble%20Min,%20Midbass%20Flat)_360_Vertical_Polar.png


Bottom line here is the majority of this speaker’s sound is radiated toward the back. Not a real surprise. But very interesting to see how a speaker like this looks in this graphical format.
 
Last edited:
OP
hardisj

hardisj

Major Contributor
Reviewer
Joined
Jul 18, 2019
Messages
2,907
Likes
13,908
Location
North Alabama
CEA-2034 (aka: Spinorama)
The following set of data is populated via 360-degree, 10° stepped, “spins” from vertical and horizontal planes resulting in 70 unique measurements. Thus, this is sometimes referred to as “Spinorama” data. Audioholics has a great writeup on what these data mean (link here) and there is no sense in me trying to re-invent the wheel so I will reference you to them for further discussion. However, I will explain these curves lightly and provide my own spin on what they mean (pun totally intended). Sausalito Audio also has a good write-up on these curves here. Furthermore, you can find discussion in Dr. Floyd Toole’s book “Sound Reproduction”. Here’s my Amazon affiliate link if you want to purchase it and help me earn about 2% of the price. And, finally, here is a great video of Dr. Toole discussing the use of measurements to quantify in-room performance.

In short, the CEA-2034 graphic below takes all the response measurements (horizontal and vertical) and applies weighting and averaging to sub-sets and can help provide an (accurate) prediction of the response in a typical room. If there is a single set of data to use in your purchase decision, this is probably it.
Alternatively, click this arrow, if you want my quick take on what these curves mean without going to another site.
Bose%20901%20Series%20V%20(No%20EQ)_SPIN.png


This is exactly why I wanted to test this speaker. I’ve never seen a set of CEA-2034 curves that looks like this. The on-axis response and the Listening Window curve is garbage. Tons of resonances. But, I don’t care about that right now. I care about the Directivity Index curves (the dashed blue and red ones).
Both the DI curves follow the on-axis response almost explicitly until it reaches the breakup point of the front full range speaker. But, mostly, the sets of curves are identical with the on-axis response. Makes sense… I mean, the front speaker is the same as the back 8 speakers. Combing between the multitude of rear speakers would pick up in the upper midrange (where they all begin beaming; neverminding the center-to-center spacing). But the listening window is subject to the same thing so the difference between these sets of curves is practically the same.
Secondly, the value associated to the DI curves is another thing that got my attention. As a point of reference, a true omnidirectional speaker - one that emits the same sound forward as it does to the sides and back - would have a DI value of 0. A front-firing speaker, like we are all used to, has a positive DI value because there is more energy being radiated forward than backward (and only backward at lower frequencies most of the time). I hadn’t considered what a speaker that is primarily firing toward the back would look like, though. But now I know. The DI values are below 0. Which indicates the majority of this speaker’s sound is being radiated behind the speaker rather than the front (the ratio of front to rear sound, really).
This is cool stuff. And for this reason alone, I am pretty excited to have been able to test this speaker in the CEA-2034 fashion.
There’s more to note here if I take my time, I’m sure. But I have to keep going so…
Below is a breakout of the typical room’s Early Reflections contributors (floor bounce, ceiling, rear wall, front wall and side wall reflections). From this you can determine how much absorption you need and where to place it to help remedy strong dips from the reflection(s). But with a speaker like this, where sound is intentionally radiated everywhere, I don’t think you’d want to place absorption anywhere other than the floor and ceiling, if anything.
Bose%20901%20Series%20V%20(No%20EQ)_Early_Reflections_Breakout.png


And below is the Predicted In-Room response compared to a general Target curve equaling -1dB/octave.
Bose%20901%20Series%20V%20(No%20EQ)_Predicted_vs_Target.png


Now, here is the same set of data for the case the EQ was in-line and set to Neutral/Flat/whatever:
Bose%20901%20Series%20V%20(Bass%202%20-%20EQs%20Neutral)_SPIN.png


Bose%20901%20Series%20V%20(Bass%202%20-%20EQs%20Neutral)_Early_Reflections_Breakout.png


Bose%20901%20Series%20V%20(Bass%202%20-%20EQs%20Neutral)_Predicted_vs_Target.png




And here is the same set of data for the case the EQ was in-line and set with Midbass Flat and Treble at minimum which I found to be the best compromise for the Spinorama set of data. Though, this didn’t give me the ideal response in my room; for that, I wound up using essentially the “neutral” EQ slider positions.
Bose%20901%20Series%20V%20(Bass%202%20-%20Treble%20Min,%20Midbass%20Flat)_SPIN.png


Bose%20901%20Series%20V%20(Bass%202%20-%20Treble%20Min,%20Midbass%20Flat)_Early_Reflections_Breakout.png


Bose%20901%20Series%20V%20(Bass%202%20-%20Treble%20Min,%20Midbass%20Flat)_Predicted_vs_Target.png





Total Harmonic Distortion (THD) and Compression
Distortion and Compression measurements were completed in the nearfield (approximately 0.3 meters). However, SPL provided is relative to 1 meter distance.
Harmonic Distortion and Compression: What does this data mean? (click me for info)

EQ not in-line (raw speaker)
Bose%20901%20Series%20V%20(No%20EQ)_harmonicDistortion_linear.png


Bose%20901%20Series%20V%20(No%20EQ)_harmonicDistortion_linear_zoom.png


Bose%20901%20Series%20V%20(No%20EQ)_Compression_Normalized.png





But what happens when you put the EQ in-line and set it for neutral?…
Bose%20901%20Series%20V%20(Bass%202%20-%20EQs%20Neutral)_harmonicDistortion_linear.png


Bose%20901%20Series%20V%20(Bass%202%20-%20EQs%20Neutral)_harmonicDistortion_linear_zoom.png


Bose%20901%20Series%20V%20(Bass%202%20-%20EQs%20Neutral)_Compression_Normalized.png


Distortion city! Ewwwwww….





Maximum Long Term SPL
The below data provides the metrics for how Maximum Long Term SPL is determined. This measurement follows the IEC 60268-21 Long Term SPL protocol, per Klippel’s template, as such:
  • Rated maximum sound pressure according IEC 60268-21 §18.4
  • Using broadband multi-tone stimulus according §8.4
  • Stimulus time = 60 s Excitation time + Preloops according §18.4.1
Each voltage test is 1 minute long (hence, the “Long Term” nomenclature).
The thresholds to determine the maximum SPL are:
  • -20dB Distortion relative to the fundamental
  • -3dB compression relative to the reference (1V) measurement
When the speaker has reached either or both of the above thresholds, the test is terminated and the SPL of the last test is the maximum SPL. In the below results I provide the summarized table as well as the data showing how/why this SPL was deemed to be the maximum.
This measurement is conducted twice:
  • First with a 20Hz to 20kHz multitone signal
  • Second with a limited 80Hz to 20kHz signal
The reason for the two measurements is because it is unfair to expect a small bookshelf speaker to extend low in frequency. Applying both will provide a good idea of the limitations if you were to want to run a speaker full range vs using one with a typical 80Hz HPF. And you will have a way to compare various speakers’ SPL limitations with each other. However, note: the 80Hz signal is a “brick wall” and does not emulate a typical 80Hz HPF slope of 24dB/octave. But… it’s close enough.
You can watch a demonstration of this testing via my YouTube channel:

Test 1: 20Hz to 20kHz
Table Results:
maxspl_table_20.png


Multitone compression testing. The red line shows the final measurement where either distortion and/or compression failed. The voltage just before this is used to help determine the maximum SPL.
Bose%20901%20Series%20V%20(No%20EQ)_MTON_Compression%2020.png


Multitone distortion testing. The dashed blue line represents the -20dB (10% distortion) threshold for failure. The dashed red line is for reference and shows the 1% distortion mark (but has no bearing on pass/fail). The green line shows the final measurement where either distortion and/or compression failed. The voltage just before this is used to help determine the maximum SPL.
Bose%20901%20Series%20V%20(No%20EQ)_MTON_Distortion%2020.png



Test 2: 80Hz to 20kHz
Table Results:
maxspl_table_80.png


Multitone compression testing. The red line shows the final measurement where either distortion and/or compression failed. The voltage just before this is used to help determine the maximum SPL.
Bose%20901%20Series%20V%20(No%20EQ)_MTON_Compression%2080.png


Multitone distortion testing. The dashed blue line represents the -20dB (10% distortion) threshold for failure. The dashed red line is for reference and shows the 1% distortion mark (but has no bearing on pass/fail). The green line shows the final measurement where either distortion and/or compression failed. The voltage just before this is used to help determine the maximum SPL.
Bose%20901%20Series%20V%20(No%20EQ)_MTON_Distortion%2080.png


The above data can be summed up by looking at the tables above but is provided here again:
  • Max SPL for 20Hz to 20kHz is approximately 81dB @ 1 meter. Both the distortion and the compression thresholds were exceeded above this SPL.
  • Max SPL for 80Hz to 20kHz is approximately 82dB @ 1 meter. The compression threshold was exceeded above this SPL.
Um, yea… this speaker has a LOT of distortion and a lot of compression. Even without EQ. The midrange distortion was glaringly obvious to my ears at some points in certain music when listening at around 90dB.





Extra Measurements


Nearfield measurements.
Mic placed about 0.50 inches - relative to the baffle - from each drive unit and port. While I tried to make these as accurate in SPL as I could, I cannot guarantee the relative levels are absolutely correct so I caution you to use this data as a guide but not representative of actual levels (measuring in the nearfield makes this hard as a couple millimeters’ difference between measurements can alter the SPL level). Plus, with a speaker like this where there are 8 drivers all together on the back, it’s hard to get an accurate nearfield measurement of the rear ports. But, nonetheless, I have provided what I measured.
Bose%20901%20Series%20V%20(No%20EQ)%20Nearfield.png




Step-Response.
Raw speaker step-response.
Bose%20901%20Series%20V%20Raw%20Step%20response.png




The graphic below shows both the “raw”, without EQ step-response (blue) as well as the step-response with the EQ in-line (red). I have also annotated the initial impulse peak and the secondary which I believe to be the rear drivers’ time of arrival (the delta in time between the two matches up to the distance between the two).
Bose%20901%20Series%20V%20Step%20Response%20Annotated.png
 
OP
hardisj

hardisj

Major Contributor
Reviewer
Joined
Jul 18, 2019
Messages
2,907
Likes
13,908
Location
North Alabama
Subjective Evaluation:
Before I dive into the subjective feedback let me first give you the layout of my room. Note that I provide two images of the listening setup. I initially tried the speakers close to the side walls and then I moved them about 3 feet from the side walls.

Also, it is important for me to make clear I listened to these in various configurations (toed in, toed out, against the walls, away from the walls, etc). I also listened to them in my downstairs living room so I could position them close to the front wall (which is about 20 feet wide), per the manual I showed above, to see how much effect the near-wall placement mattered. While it did change the effect of the soundstage, for the most part, it was the same result - tonally - I had in my main listening room upstairs. I am not providing pictures of that setup because my living room wall is a built-in bookcase and I don't want people zooming in on pictures of my family. That's weird.

I always try to listen to speakers in different settings to see if one is more suited for a particular speaker and in this case the difference was more minimal than I expected. Obviously your mileage may vary depending on your specific setup.

HT2.png


DSC06332.JPG


DSC06336.JPG


DSC06104.JPG


If the false wall part is odd to you, here's some background. I don't like seeing speakers when watching a movie. So, I built a false wall and used an acoustically transparent screen with speakers behind it. The wall is only 2x4's; no panels of wood or anything. Just a skeleton of a wall to give me something to attach the screen and acoustic treatment to. There is 2-inch wedge foam affixed to the 2x4 studs and between the false wall and back of the room are the front speakers (L/C/R & 18-inch subwoofers).


My demo music:
(see site)


Subjective Analysis Setup:
  • I listened to these in my downstairs living room so I could position them close to the front wall (which is about 20 feet wide) to see how much effect the near-wall placement mattered. While it did change the effect of the soundstage, for the most part, it was the same result I had in my main listening room upstairs. I always try to listen to speakers in different settings to see if one is more suited for a particular speaker and in this case the difference was more minimal than I expected. Obviously your mileage may vary.
  • The EQ was always in-line in my listening sessions. I only measured them without to get an idea of the raw speaker performance. But I listened to them with the EQ.
  • I listened to these various ways: with the speakers near the side wall, with the speakers 3 feet from the sidewalls. With and without Dirac Live. I will make notes where applicable to define the specific listening conditions.
  • I used Room EQ Wizard (REW) and my calibrated MiniDSP UMIK-1 to get the volume on my AVR relative to what the actual measured SPL was in the MLP (~11 feet from the speakers). I varied it between 85-90dB, occasionally going up to the mid 90’s to see what the output capability was. In a poll I found most listen to music in this range.
  • Components: Oppo BDP-103 playing music off my thumb drive feeding signal via HDMI to a Denon AVR-X4000 which then feeds in to a refurbished Adcom GFA-545 for power.
I listened to these speakers and made my subjective notes before I started measuring objectively. I did not want my knowledge of the measurements to influence my subjective opinion. This is important because I want to try to correlate the objective data with what I hear in my listening space in order to determine the validity of the measurement process. I try to do a few listening sessions over a couple days so I can give my ears a break and come back “fresh”.


First listening test. Without Dirac Live.
I tried various EQ settings and measured the in-situ response. Here are the ones I captured using REW:
In-Room_without_DL.png




I decided that I liked the almost-neutral setting where the difference was just a touch lower on the MidBass slider and a touch more on the MidTreble slider which is the orange line above.
There are still so many variations that I listened to this speaker in (against the side wall, away, changing EQ, leaving it flat) that I think it might be better to give some general notes rather than specify each individual situation and note the differences. So I’ll do that.
  • This speaker displayed significant distortion when pushed in to the mid-90’s at my listening position. It was most aggressive in the midrange between 200-800Hz.
  • The imaging and soundstage of this speaker is like nothing I’ve ever heard before. It doesn’t immerse you. But it immerses the area where the speakers are. Typically a soundstage will extend to the side, frontwards and backwards of the speaker. But only with certain music does the soundstage really expand (as it should, of course). However, with the 901’s the soundstage is deep and wide on everything I threw at it. It still changed the size depending on the recording, though.
  • Seating position practically doesn’t matter. I know we all talk about speakers having a wide sweet spot. Well, these don’t even have a sweet spot. When I sat in the side chairs of my front row the vocalist still came from between the two speakers. I would hear things now and again where the vocalists’ voice would move at a certain frequency. But compared to what happens when you move a seat over; where the vocalist follows you… well, the 901’s do not do that. The center stays at the center (for the most part). It’s mind-boggling.
  • Even when using the best compromise of the EQ sliders, this speaker was a wreck, tonally speaking. There were sharp upper treble tones. The enclosure sounded very boomy and made listening to male vocals at any appreciable volume nearly unbearable. I wrote in my notes from listening that the midrange between 500-800Hz seemed “recessed”. I’m looking at the data and the only thing I can make the connection to is the fact that the lower midrange/upper midbass is so high in output that it makes the upper midrange sound this way.
  • I switched the Philharmonic BMR speakers back in for these and was quickly reminded of everything the Bose 901’s do wrong. But I was also reminded of everything a conventional speaker just cannot do.

Second listening test. With Dirac Live.
I took the setting above and let Dirac Live do its thing. It smoothed the response right out and I got this at the measurement position.
In-Room_with_DL.png


There. That’s better. A lot better, tonally. Still, the distortion was present so they couldn’t be pushed that hard. Even when using a crossover of 80Hz. Which stinks. But if you own a pair of these and want to improve the sound get yourself Dirac Live. I recommend MiniDSP’s products. A simple MiniDSP DDRC-24 as the conduit for Dirac Live to do its thing will make a significant improvement.


Bottom Line
Look, this speaker isn’t a speaker you buy for accuracy. This is the speaker you buy because you’re looking for something different.
I honestly was enamored with what they do. It was so wildly different than anything I’ve heard before that, at first, I pretty much ignored all its flaws (and there are some big ones). The soundstage is crazy big. The sound comes from everywhere in front of you, but still does a good job of having good image placement. It’s not a “wall of sound”. It’s a “prism of sound”. It’s not 2-D (and, really, even some of the best speakers still don’t render a 3-D space). The 901 isn’t even 3-D. It’s 4-D. Heck, it’s 6-D. It’s a total mind trip. But the tonality is a wreck. Dirac Live fixed that up well for me, though. Unfortunately, there’s no way to get around the considerably high distortion and SPL limitations. I wonder how a design like this could be made to sound if you just replace the front full range speaker with a modern 5-inch midrange and tweeter.
If you haven’t heard the Bose 901 speakers, I encourage you to find a pair and give them a listen. If for no other reason than to understand what else is possible. Because if this speaker’s performance could be improved tonally and its SPL limits increased, I believe there would be a lot of people interested. Myself included. So, ask around… you probably have a friend with a pair that would be happy to let you hear what this whole direct/reflecting thing is all about. Don’t expect to be wowed. But maybe expect to smile and laugh a few times when they do something you’ve never heard a speaker do. I know I did.


Contribute
If you like what you see here and want to help me keep it going, you can donate via the PayPal Contribute button on this page. Since this item was loaned to me for testing I am having to pay round trip shipping which is about $230. If you can help by chipping in a few bucks I would truly appreciate it.
 
Last edited:

CDMC

Major Contributor
Forum Donor
Joined
Sep 4, 2019
Messages
1,172
Likes
2,321
In short, way cool. I believe they would perform a bit better in an untreated room, closer to the backwall, but your description of their sound is how I remember them. I would love to see a 701 Series iii measured, as I remember those sounding the best.
 

Sonny1

Active Member
Joined
Apr 5, 2020
Messages
252
Likes
350
Wow! I appreciate you taking the time to measure these. I heard a pair when I was a teenager at a friend’s house. His dad had a pair and wouldn’t let us mess with them. It was a long time ago and I had never heard a real audiophile system. I don’t recall being particularly impressed by them but I was impressed that his dad dedicated a large part of their house for an audio system.

A neighbor once offered me a free pair of these for helping move some junk out of their attic. I accepted a beer instead (they gave me a six pack). Looks like I made the right choice. They are fun for a novelty but these speakers, while being unique, are a very odd design. It’s great to finally see measurements.
 

617

Major Contributor
Forum Donor
Joined
Mar 18, 2019
Messages
2,404
Likes
5,296
Location
Somerville, MA
Like this comment if you want me to design a modern adaptation of these with smoother response and better drivers. I am so goddamned tempted.
 

thewas

Master Contributor
Forum Donor
Joined
Jan 15, 2020
Messages
6,762
Likes
16,228
The Bose 901 is one of the all time loudspeaker classics since more than now 50 years and there have been so many reviews about its different iterations but not one of them is not even close as good and detailed to yours, only your review really lighted it up so well from all sides and aspects, so you have my upmost respect for that!
Also only your review made me now wanting to build just out of fun and curiosity a modern version for it with low distortion drivers, I also want now this "mind trip"!
Congratulations on this level of review excellence!
 

MZKM

Major Contributor
Forum Donor
Joined
Dec 1, 2018
Messages
4,244
Likes
11,485
Location
Land O’ Lakes, FL
Can we get a formula score for these from @MZKM. Or how negative can a rating be with the formula.

Man is this a great website or not? Nowhere else can you get this kind of information. Thanks Erin.
I can’t compute scores from just graphs (others on here can digitize graphs into data points), for mine, the horizontal/vertical data needs to be in the same format as the one Amir posts.
 

Blumlein 88

Grand Contributor
Forum Donor
Joined
Feb 23, 2016
Messages
20,524
Likes
37,057
I can’t compute scores from just graphs (others on here can digitize graphs into data points), for mine, the horizontal/vertical data needs to be in the same format as the one Amir posts.
I was wondering if Erin can provide the data in the form you need.
@hardisj
 
OP
hardisj

hardisj

Major Contributor
Reviewer
Joined
Jul 18, 2019
Messages
2,907
Likes
13,908
Location
North Alabama
I can’t compute scores from just graphs (others on here can digitize graphs into data points), for mine, the horizontal/vertical data needs to be in the same format as the one Amir posts.

I used VirtuixCAD to spit out the files in to a more user friendly format and uploaded the zipped files to DropBox. I have attached 3 links below. The name of the zip file tells you what the data is from.

Speaker only. No EQ in-line.
https://www.dropbox.com/s/igf613r05tnztxi/Bose 901 Series V (No EQ).7z?dl=0


Bass 2 - Neutral EQs
https://www.dropbox.com/s/e0qby8mq50psl1e/Bose 901 Series V (Bass 2 - EQs Neutral).7z?dl=0


Bass 2 - Treble Min, Midbass Flat (best of the bunch that aligns with the target curve but not what sounded the best)
https://www.dropbox.com/s/dl6huo8mzfeaq7m/Bose 901 Series V (Bass 2 - Treble Min, Midbass Flat).7z?dl=0
 

tmtomh

Major Contributor
Forum Donor
Joined
Aug 14, 2018
Messages
2,636
Likes
7,497
What a completely bananas speaker design. Thank you so much for this incredibly detailed review. It's amazing how decades of imprecision and BS written about this speaker are clarified and wiped away with this kind of info. Well done!
 

MZKM

Major Contributor
Forum Donor
Joined
Dec 1, 2018
Messages
4,244
Likes
11,485
Location
Land O’ Lakes, FL
I used VirtuixCAD to spit out the files in to a more user friendly format and uploaded the zipped files to DropBox. I have attached 3 links below. The name of the zip file tells you what the data is from.

Speaker only. No EQ in-line.
https://www.dropbox.com/s/igf613r05tnztxi/Bose 901 Series V (No EQ).7z?dl=0


Bass 2 - Neutral EQs
https://www.dropbox.com/s/e0qby8mq50psl1e/Bose 901 Series V (Bass 2 - EQs Neutral).7z?dl=0


Bass 2 - Treble Min, Midbass Flat (best of the bunch that aligns with the target curve but not what sounded the best)
https://www.dropbox.com/s/dl6huo8mzfeaq7m/Bose 901 Series V (Bass 2 - Treble Min, Midbass Flat).7z?dl=0
Uhh, that'd be a total of >200 files I'd have to import and adjust. Maybe leave this to the people who can digitize Spinorama graphs.
 

DonH56

Master Contributor
Technical Expert
Forum Donor
Joined
Mar 15, 2016
Messages
7,835
Likes
16,498
Location
Monument, CO
My experience with Bose 901's began with the very first somewhat crude model and I have heard them many times since, sometimes in very good systems. They had (and still do apparently) very high distortion, not unexpected given their design, but what turned me off was the very feature that others prize -- the very "wide", "spacious" sound stage. It is very impressive at first listen, and remains so for some material, but too much of the time the wandering, broad image left me thinking they were a good "showpiece" speaker but were not something I could/would listen to day in and day out. Just got tired of vocals that wandered all over the room going up and down the scale instead of staying put, and of the infamous 9' violins and other solo or individual instruments that were spread (I might even say "smeared") across the room. A sparkler turned into a huge fireworks display is impressive, but no longer a sparkler...

Somewhat interesting is the original Stereophile review by J. Gordon Holt himself: https://www.stereophile.com/standloudspeakers/425/index.html -- I remember this review as it aligned well with my impressions at the time, back when they were new and several friends (and stores) jumped on the bandwagon. The final paragraph:

"If we were to judge the 901 in terms of the best sound available, then, we would say that it produces a more realistic semblance of natural ambience than any other speaker system, but we would characterize it as unexceptional in all other respects. It is ideal for rock enthusiasts to whom sheer sonic impact is of paramount importance, and for classical listeners who want the next best thing to ambient stereo without the cost and the bother of rear-channel add-ons. However, we doubt that the 901 will appeal to perfectionists who have developed a taste for subtleties of detail and timbre."
 
Last edited:

krabapple

Major Contributor
Forum Donor
Joined
Apr 15, 2016
Messages
3,169
Likes
3,717
I had a pair of Type IVs for years..even hung them from the ceiling at one point. They were fun but a pain to move.

Back in long ago Internet days there was an audiophile who made a pretty good case for Bose...or Bose-like -- setups. He had a bunch of them arrayed around a room. Also reportedly his Bose-style speakers outperformed other speakers in a well-designed shoot out. I forget his name now...though I think his last name started with Em..something?

I don't get why you toed yours in though....it's not what Bose recommends....

Btw I knew a guy who preferred to listen to his turned around (i.e., the array and rocket ports facing forward). It takes all kinds.
 
Last edited:
Top Bottom