• Welcome to ASR. There are many reviews of audio hardware and expert members to help answer your questions. Click here to have your audio equipment measured for free!

3e Audio A5 Stereo Amplifier Review

Rate this amplifier:

  • 1. Poor (headless panther)

    Votes: 6 1.5%
  • 2. Not terrible (postman panther)

    Votes: 16 4.1%
  • 3. Fine (happy panther)

    Votes: 67 17.2%
  • 4. Great (golfing panther)

    Votes: 301 77.2%

  • Total voters
    390
Hey guys, I see many posts of people swapping the right and left channel op amps on this amp, which I guess are the obvious ones to swap, but what about the other single-end to balanced conversion op amp - especially if you are using the single ended input - wouldn't that be worth trying as well? Has anyone here swapped that op amp? Any feedback on why, even if only using the single ended input, it would still be best to leave the conversion op amp alone and only focus on swapping the right and left balanced op amps? I assume if you use the balanced inputs on amp, the conversion op amp gets bypassed, but if you are using the single ended input, then it's in use and in theory can be swapped for 'tuning' just like the others? I just don't ever see anyone talk about the conversion op amp or see pics of it being swapped and am curious ..maybe most simply use the balanced input, so swapping the conversion one doesn't matter? Thanks!
 
Last edited:
Hey guys, I see many posts of people swapping the right and left channel op amps on this amp, which I guess are the obvious ones to swap, but what about the other single-end to balanced conversion op amp - especially if you are using the single ended input - wouldn't that be worth trying as well? Has anyone here swapped that op amp? Any feedback on why, even if only using the single ended input, it would still be best to leave the conversion op amp alone and only focus on swapping the right and left balanced op amps? I assume if you use the balanced inputs on amp, the conversion op amp gets bypassed, but if you are using the single ended input, then it's in use and in theory can be swapped for 'tuning' just like the others? I just don't ever see anyone talk about the conversion op amp or see pics of it being swapped and am curious ..maybe most simply use the balanced input, so swapping the conversion one doesn't matter? Thanks!
Aside from the fact that op-amp rolling is a pointless gimmick (you can find plenty of information on this—including measurements—at ASR), the conversion to a balanced signal takes place within those very swappable op-amps—after the stereo potentiometer—and nowhere else.
The OPA at the input is used to de-symmetry the balanced input, not to symmetry the RCA input.
 
So the OPA shown in top left corner of picture 'single-end to balance' you're saying doesn't convert anything and is there to de-symmetry the balanced input not to symmetry the rca input? The conversion happens with the other two OPA shown on each side of potentiometer? ..sorry, trying best to follow. What does de-symmetry mean? Thanks
Aside from the fact that op-amp rolling is a pointless gimmick (you can find plenty of information on this—including measurements—at ASR), the conversion to a balanced signal takes place within those very swappable op-amps—after the stereo potentiometer—and nowhere else.
The OPA at the input is used to de-symmetry the balanced input, not to symmetry the RCA input.
 

Attachments

  • Screenshot_20260916-105941.png
    Screenshot_20260916-105941.png
    410.1 KB · Views: 90
Last edited:
So the OPA shown in top left corner of picture 'single-end to balance' you're saying doesn't convert anything and is there to de-symmetry the balanced input not to symmetry the rca input? The conversion happens with the other two OPA shown on each side of potentiometer? ..sorry, trying best to follow. What does de-symmetry mean? Thanks
In other words the balanced input gets converted to unbalanced by that single OPA then gets converted back to balanced by the pair of OPA on each side of potentiometer? RCA input would bypass that single OPA and go straight to pair of OPA on each side of potentiometer for conversion to balanced?
 
Last edited:
In other words the balanced input gets converted to unbalanced by that single OPA then gets converted back to balanced by the pair of OPA on each side of potentiometer? RCA input would bypass that single OPA and go straight to pair of OPA on each side of potentiometer for conversion to balanced?
It looks that way, which is a good thing. The pot appears to be a 2-gang (with button) rather than the 4-gang that would be needed if the signal was balanced at the pot. It'll get better CMRR for the balanced input that way, and work properly with impedance balanced sources. See "The G Word" for details.
 
Have there been any new HW iterations for this amp since last year?
 
Have there been any new HW iterations for this amp since last year?
I am not aware of any changes so far.
Of course, it is always possible that components (of equivalent quality) may vary slightly depending on availability.
 
I am not aware of any changes so far.
Of course, it is always possible that components (of equivalent quality) may vary slightly depending on availability.

Part of the inquiry is because I've seen two separate listings on Amazon for this amp -- one just lists it as normal, and the other says, "next-gen" in the listing title, but it's also "unavailable." I've also learned that they've maybe changed their name to Alsozone? And the storefront has the A5/A7 amps (though also listed as unavailable), and these GaN monoblocks that seem tempting (though looking at the thread for those here, they seem to be a lot noisier than the A series based on some user feedback). There also seems to be some indication that these amps are being discontinued?
 
Part of the inquiry is because I've seen two separate listings on Amazon for this amp -- one just lists it as normal, and the other says, "next-gen" in the listing title, but it's also "unavailable." I've also learned that they've maybe changed their name to Alsozone? And the storefront has the A5/A7 amps (though also listed as unavailable), and these GaN monoblocks that seem tempting (though looking at the thread for those here, they seem to be a lot noisier than the A series based on some user feedback). There also seems to be some indication that these amps are being discontinued?
The problematic A5's were available for a very short time, less than a month on 1st release. If you purchase on Amazon with 3e Audio as the vendor you will get the non-problematic version for sure. GAN is at this point a totally separate discussion.

The A5 and A7 are attractive because of their measured performance. The GANs have not yet been measured. The primary benefits of GAN seem to be high power with high efficiency (so, little heat) in a small package. If you need the High Power then the A5 is not the best choice (choose a TPA3255 like the A7). More direct competitors to the A5 would seem to be the Topping Mini 300 or PA3s. I cannot see reasons those would be superior, but they are more aligned in concept and are a bit cheaper.
 
Last edited:
The problematic A5's were available for a very short time, less than a month on 1st release. If you purchase on Amazon with 3e Audio as the vendor you will get the non-problematic version for sure. GAN is at this point a totally separate discussion. The A5 and A7 are attractive because of their measured performance. The GANs have not yet been measured.

What are the differences between the problematic/non-problematic versions with regards to the results of this review (outside of the 12v trigger that was only in the pre-production model)?

I have an A7 (purchased, I think, February last year), but I don't need that much power for my nearfield desktop system anymore.
 
What are the differences between the problematic/non-problematic versions with regards to the results of this review (outside of the 12v trigger that was only in the pre-production model)?
Not problems really, annoyances. The auto shut off happened too quickly for some, and required too high a signal..so it might shut off with soft music playing. Those were fixed, and the ability to disable auto-shut off was added. As a result, it is simple to see if you have the less annoying version by turning on and off the shut off feature.

For lower power needs the A5 is great. I am also a fan of the older MA12070 series Infineon amps for desktop. The Loxjie A30 measures great and has a DAC, Remote, Display, Tone Controls...so the opposite of 3e but pretty nice on a desktop.
 
Last edited:
Not problems really, annoyances. The auto shut off happened too quickly for some, and required too high a signal..so it might shut off with soft music playing. Those were fixed, and the ability to disable auto-shut off was added. As a result, it is simple to see if you have the less annoying version by turning on and off the shut off feature.

I was hanging around these threads during those discussions, so I am familiar with that topic. My edit may have been missed, but the A7 I have (purchased around February 2025) does have the ability to disable auto-sensing.

If that's the only difference then it would be the same as when I would have last participated in the threads roughly a year ago.
 
Part of the inquiry is because I've seen two separate listings on Amazon for this amp -- one just lists it as normal, and the other says, "next-gen" in the listing title, but it's also "unavailable." I've also learned that they've maybe changed their name to Alsozone? And the storefront has the A5/A7 amps (though also listed as unavailable), and these GaN monoblocks that seem tempting (though looking at the thread for those here, they seem to be a lot noisier than the A series based on some user feedback). There also seems to be some indication that these amps are being discontinued?
I've seen "next-gen" headlines with amp, pffb, ti etc. some times. That's just the vendor texting.

Alsozone was spawned, many models available on amazon, two models now at audiophonics.

Unclear if the A5/A7 will run out. Those are equivalent to PAM152 and PAM252. For me it would be a case of "discontinued because of huge success". ;)
 
There also seems to be some indication that these amps are being discontinued?
I don't see such indication, at least not yet.

3E AUDIO have not only registered the Alsozone brand name but also the matching .com domain:


The also sell the A5 and A7 series of amplifiers through this new website.
 
3 Alsozone models, not 2, are available at Audiophonis a stereo amp with 3255, a fur channle amp with 3255 and a very little but powerful mono with GaN tech.
They all seem to be quite OK for their price.
 
I don't see such indication, at least not yet.

3E AUDIO have not only registered the Alsozone brand name but also the matching .com domain:


The also sell the A5 and A7 series of amplifiers through this new website.

It's largely based on this post:


And also -- at least on Amazon Canada -- some are listed "unavailable" even in the Alsozone storefront.
 
And also -- at least on Amazon Canada -- some are listed "unavailable" even in the Alsozone storefront.
This has happened before on AliExpress. One batch may be sold out.

Maybe Audiophonics discontinued this model and yes, maybe 3E AUDIO did. These discussions are no proof, though.
 
I picked up the 3e A5 during the 2 or 3 day Amazon deals days last week...$165 bucks.

What a phenomenal amplifier. I've had no issues or problems over the last 7 days..while it runs almost 24/7. Don't be fooled by it's miniature chassis & low voltage power brick. This is a legitimate amplifier. The measurements don't lie.

3e Audio did a fabulous job designing this low budget priced amp with outstanding performance. I don't know what else to say..just wow. This sub $200 amp has been pushing my Mofi 8's just as nicely as some other amps costing far more in price.
Great job 3e Audio.
 
Do you worry about clipping at the output of the amp or about a too high input signal overdriving the input stage?

The clipping LEDs will indicate clipping of the output. You cannot increase the amplifier's headroom (how much power it can output cleanly) by lowering the volume setting. The opposite bus also true, turning the volume all the way up (or setting the switch on the back to the bypass position) cannot decrease its headroom.

According to the manual the input sensitivity is 1.75 V. If I did the math correctly this applies to the low gain setting, which you are using. 3eAudio don't explicitly specify the maximum input voltage but at 100 % volume the amp will reach its maximum power output of 140 W per channel into 4 Ω when fed those 1.75 V. If your source can output more than that there is a potential danger of driving the power section into clipping.

The clipping indicators will be warning you in this case (if your hearing didn't before). If you didn't see them come upmeven once then you're probably safe. Turning down the volume on the power amp won't really help unless you are willing to sacrifice the available loudness.
 
Back
Top Bottom