sub woofers

I’m running a R26 DAC (happily) into a Madrigal Proceed AVP2 Pre/Pro (baby Levinson). I only listen to Stereo Sound (no effects, no HT). I have run dual subs historically, however, I just learned I’ve been listening to the Proceed’s internal DAC! It sounds and has sounded “good” to me. Unless I...

I've got a Sumiko S.9 sub that I hope to connect to my amplifier wirelessly. The Sumiko Wireless kit is quite old, I can't find any specs on them, and I'm concerned about timing errors. I've been looking at the various Wireless REL solutions but I'm unsure of the quality and which would be best...

When I bought my REL sub I used the high level connection as the instructions recommended. My amp was class AB, and that was the first case explained in the instructions. The high level cable has 3 wires: black, red, yellow. For an AB amp, you connect the red and yellow wires to the red binding...

I've been doing a lot of learning since discovering ASR recently. When it comes to subwoofers, I find a lot less data (at ASR and in general), and more of brand-loyalty or brand-shaming than for other areas at ASR. Even in the subwoofer comparison thread by sweetchaos, the frequency response...

Hello! This seems like the right place to ask about setting up a new speaker system. I recently found a pair of knight kn3030k 3-way speakers for a screaming deal. After that, I needed to fill out the rest. I got a polkaudio psw108 subwoofer, and a Sony str-dh190 receiver. Plus some speaker...

Help wanted to connect a subwoofer to active speakers. Active speakers are connected via balanced in the RME ADI 2 DAC FS Question 1: Can i use the unbalanced out of the RME to connect to the subwoofer low level in ? Question 2: If yes to question 1. Do i need to make any EQ changes from the...

Hi I have a Bluesound Powernode (latest version) and Q Acoustic 3050i speakers (6 ohm, 100 wpc,) and I am very happy with the sound and performance. But...when I increase the bass to 4 and treble to 2 on the tone controls it sounds great but after an hour at very high volumes (75% approx of...

Hi I have a Bluesound Powernode (latest version) and Q Acoustic 3050i speakers (6 ohm, 100 wpc,) and I am pretty happy with the sound and performance. But...when I increase the bass to 4 and treble to 2 on the tone controls it sounds great but after an hour at very high volumes (75% approx of...

I’m wondering if upgrading my sub from KEF Q400 to one of the below candidates would have a noticeable impact? In that case which sub (and size) would you go for? - REL T7X - KEF KC62 - I considered SVS Micro 3000 and loved the app, but I don’t like how it looks. So unless it’s significantly...

I have been experimenting with my LS50 and Sub KEF Q400 for several years, and still cannot find the optimal sweet spot for crossover and sub volume. The issue is that I find a good setting based on one song and album (let's say Diana Krall - Wonderful) but later when I listen to another album...

I have a Pair of KRK 8G4 monitors connected to a KRK10S2 Subwoofer , I have crossover options from 60 to 90Hz on the back side of the woofer I am not an audio professional I just use them for listening to music and watching movies , I started testing with my ears and using my mobile app phone...

Hello everyone, I'm getting used to using REW with my UMIK-1, along with setting EQ curves for my 2 subwoofers using a MiniDSP 2x4HD. This is a pretty standard auto-EQ I did for my subs with a mini house curve. I didn't really do any individual tweaking yet (there are definitely a couple of...