Search results

"Everything sounds great, sinus wave measurements are all we need to know, no actual listening required. Also, only authorized manufacturers should perform magical acts of soldering." I get it. I forgot why I stopped coming around here.

Assuming that WE don't understand, just because... is what? The phrase "Randomly adding" is derogatory, when the question was specifically about bypass caps, a normal and well understood process. It's even shown on TI documentation and there are numerous white papers about those. Nobody talked...

The passive network component values are already provided by TI... So IDK what they hide. https://www.ti.com/lit/an/slaa788a/slaa788a.pdf

So we want to be fanciful. Why are you a hater?

Take a picture that shows the OpAms above those modules, and the underside of that board too. I wonder if it's a PFFB network inside those. https://www.ti.com/lit/an/slaa788a/slaa788a.pdf I think too that bypass capacitors are always required over electrolytic ones in power stages, maybe they...

That's not what I said, it's a strawman argument. I said that steady state tests are not enough. And people above contradicted me (with a childish meme). Now you're telling me that there are tests done here for IMD - like I denied that, or I don't know about those, it's something new. I...

When you test with ONE sine wave, low frequency (333Hz or 1kHz), constant amplitude, that's "steady state". There are tests that are more advanced than that, but since they are hard to understand, some people refuse to "believe" in them. Like some people refuse to believe the Earth is a...

The chips in Schiit are different, more modern, but yeah, those older 18 bit multibit DACs sound great IMO. Remember, the CDs have 16 bit and they are sufficient. I have bought a few CD players and I can compare the multibit ones with noise-shaped delta-sigma. I prefer the multibit...

Because that's not that much different from moving a membrane, attached by a coil, with some electromagnets, suspended by a quasi-linear elastic support, in a magnetic field. Speakers, headphones have to feed-back mechanisms either...

Any assertion that an electronic device that measures well in steady state will sound good with music is just wishful thinking, not supported by anything. Blind tests proved that many times, but they are just treated as "anecdotal" by zealots of steady state measurements.

If you assume that SINAD is all you need from an amp, then yes you are right. If you listen to steady state sin waves that is perfectly true. Now, 87 dB is from where? I didn't see that at all: https://www.schiit.com/public/upload/PDF/Schiit%20Amp%20APx555%20Standard%20Test%20Suite_%20Vidar%202.pdf

Flyer for the system:

If the other devices would be ideal, theoretically perfect, then yes, they won't color the sound reproduction. But they are not. Some people look at steady-state measurements and think that's all you need to know about audio equipment. And then they cannot accept that a good "steady state...

I like J-FETs too on input stages, because they are fast and noiseless. But I think your design doesn't have enough open loop gain to be problematic. It works? yes. But is not trivial, you have to match those transistors to lower the THD. That i snot trivial to scale in manufacturing. I like...

Mani 2 has good potential, three per channel newer Jfet input OpAmps...

I don't doubt you have results. I tried it both ways and like it better the passive way... Most of the implementations NFB are not great because is not that "trivial" like you said. Throwing in an OpAmp is trivial. But not that great IMO.

And that's the fallacy... "it's trivial". While for passive networks is just simple reality.

A dedicated stereo amp will be better built than a costumer grade multichannel AVR that costs the same (or less). This is the schematic of the phono stage in your Marantz PM7000N, differential pairs of J-fet in front of a "normal" OpAmp stage, yielding better SNR (87 dB VS 74 dB usual value for...

I am a DIY EE and was, in younger days, a professional electronics repair technician. I built my own phono stages and with experimentation I found out that is better to have them as close as possible to the cartridge. Inside the player was the best location. Connection with the coil was done...

I usually look at the schematics if I can find them... Most of the time you're finding that the stage in a flagship AVR is very similar with what you get in a stand alone. Denon reuses the same MM preamp in their latest models, it is rated at 74 dB SNR... Usually on modern models is just an...