Search results

Alright, still figuring out this whole MSO thing but I have a couple of specific questions about room treatment after playing around with AMROC and the Porous Absorber simulator. It looks like 4in panels with a 4in gap will reach down lower. I think this makes more sense for the living room...

Going to run some MSO this week to get my sub integrated. All the guides I have found seem to assume multiple dedicated subs, rather than a sub + fullrange mains - could anybody point me in the direction of some resources that might help me do this?

Sounds like I still may see some benefit from treating the windows behind me and the walls behind the speakers, to damp those early reflections. Unfortunately, the MiniDSP doesn't support Dirac Bass MGMT, so it's going to be a combination of MSO + Dirac, MSO for the subs and Dirac for the full...

Okay disabling the subwoofer moved the issue to ~58Hz - Here are my new measurements. I'm not entirely convinced it's not a room mode issue. I've ordered some OC 703 panels and fabric, going to build absorption panels for both rooms as a "starting point" for treatment (placed at 1st...

I let some friends borrow them for a party in college. Never again... When I have more time/funds I will source a replacement driver, it really is an eyesore and no amount of vacuuming did anything. Where does the shim go? Between the sash and the frame in the plane of the wall? That may...

I do see that. I have some flexibility in speaker placement, so might be able to shift the frequency of the cancellation. I suspect the subwoofer may be involved (just now realizing I forgot to turn it off, so the "full range" measurements are full-range as in frequency, not as in "measuring...

Alright, here's measurements, floor plans, and some photos. It sounds noticeably better with Dirac. I am planning on putting in cellular shades in my studio hoping that they do a little bit better than the wood shades I have now. Hoping to get the rooms treated by Thanksgiving, please advise...

Hey all, have been lurking for a couple years, was going to build the LX521.4 but my room at my new place is too small (Roughly 25x12ft, combined living and dining area) - just moved into a new place and getting my system setup. At my prior apartment, I had a larger room with the back wall...

The okto seems awesome, had my eyes on it for a while when this system was only planned to be 8 channels. My concern is being able to synchronize the two devices with the latency I need, since them being even 1 or 2 samples out of lockstep could introduce phase issues into my system, at least...

I need to sit with that thought for a bit, the idea of a fan bugs me quite a bit, but I do like the hardware. In my current setup, my turntable noise floor is HIGH, I think because of disgusting mains power in the walls that my system picks up, so I couldn't do always-on loopback without...

I've heard not so great things about Antelope drivers and support. Wouldn't be an issue if I didn't want to do linux eventually. Haha welcome to the world of audio interfaces - they are counting digital outputs, over ADAT/AES etc. as part of that channel number. That number is just the number...

Thanks, this basically sums up my thoughts on live sound stuff that were previously scattered around various tabs and forum posts. It seems like the tradeoffs are either in raw horsepower or in architecture complexity, right? I'd love to find a solution that doesn't have a PC, though a headless...

Volume control in the PC seems like the way to go. Maybe Volume control in the box seems like the way to go. Maybe I can even do a motorized pot into ADC and use a remote to trigger the motor, make it feel like an analog control haha. The merging stuff seems interesting... Does it just...

If this isn't a joke, I'm not particularly trying to write TOO much code, but would consider it if USB weren't so annoying to implement. Some of the SHARC chips seem to have the DSP horsepower to meet my needs, and C++ libraries so I'm not writing assembly. However, there MUST be a way to do...

USB to GPIO can't be that hard. Do you know where the code for the rpi GPIO lives/runs, or more generally, how can I hook external software into camilla? I'm imagining a sort of "control console" that lives in my rack, that talks to the DSP linux instance over USB, and in there just have an...

Michael, I've spent a lot of time reading your posts, both here and on OPLUG, thanks for chiming in. I do think that a PC-based solution is going to be the way to go with this one, and it comes down to finding interfaces with enough outputs that work on linux (I'd go for MacOS if I could...

This is quite interesting, I like the add-on card approach, could start with 8 channels, and the DACs seem fantastic if they perform as stated. This still necessitates a PC in the signal chain for DSP and crossover duty though.

Now that I've graduated college and have a little more time and money, I figure it's time I start putting together my dream listening room. I've been poking around the forums a bit, and have been trying to figure out how to solve the DSP link in my signal chain. Unfortunately, the DAC8 pro has...