Search results

  1. M

    JBL Stage A130 Review (speaker)

    What about JBL Stage A100 P sub? It’s a lot cheaper than those from SVS
  2. M

    JBL Stage A130 Review (speaker)

    @staticV3 Any suggestion on a good price/performance ratio SUB with RCA input/s?
  3. M

    JBL Stage A130 Review (speaker)

    Ok, so... I need an active SUB; I can connect A90 pre RCA outputs to RCA input on the SUB; If the SUB I'll buy has only a single RCA input, I will need RCA splitters (male to female) A90 pre support simultaneous output from the RCA and the XLR but, isn't the RCA output 6db lower than the XLR...
  4. M

    JBL Stage A130 Review (speaker)

    I would prefer SOLUTION n.2. So… dac > rca > sub; dac > xlr > amp. I’m right? QUESTIONS So do i need an active sub? Do I need to connect only one of the RCA outputs to the SUB or both? Since i use a PRE (A90) between the DAC and the AMP, is it the same? RCA outputs > SUB? Given that the...
  5. M

    JBL Stage A130 Review (speaker)

    @staticV3 What is an high pass filter and why I would need it for the A130?
  6. M

    JBL Stage A130 Review (speaker)

    Ok, o get my Jbl A130 and I’m listening to them. Until now I think I’m happy with the sound. Not as bright as B&W. But, obviously, the bass response of a full tower speaker is missing. So I’m wondering if I can connect a subwoofer. But how to do it since my amp (Audiophonics HPA S400ET) has...
  7. M

    JBL Stage A130 Review (speaker)

    Has the floorstanding big brother JBL A190 same level of performance as the A130 here reviewed?
  8. M

    JBL Stage A130 Review (speaker)

    I would like to buy these speakers to start educating my ear to good sound (I have some terrible B&W currently) but I'm afraid to burn them if I feed them with my amp (Audiophonics hpa s400et, 200w 8Ohm / 400w 4Ohm) since these speakers are rated 25watt. It's safe if I don't increase too much...
  9. M

    Audiophonics HPA-S400ET Review (Stereo Amplifier)

    But I have another question. I’m not an expert but I’m curious and since I’m studying and discovering audio science world little by little tanks to this forum, in the Audio Precision literature I read about parameters like “slew rate” or/and “rise time” and, If I got it right, It has to do...
  10. M

    Audiophonics HPA-S400ET Review (Stereo Amplifier)

    Solved! :) I changed my old speaker cable with new Canare 4S11 and now all is ok. Low frequencies are now present and powerful. I don’t feel any lack anymore. Especially if I go up in volume, but also at lower volumes. So I use M gain on Topping A90 and buffer bypass on the Audiophonics. It...
  11. M

    Audiophonics HPA-S400ET Review (Stereo Amplifier)

    I don’t hate you because my B&W are yet on eBay and my next purchase is Revel M16 ;)
  12. M

    Audiophonics HPA-S400ET Review (Stereo Amplifier)

    It’s ok to use the digital volume control? Any loss?
  13. M

    Audiophonics HPA-S400ET Review (Stereo Amplifier)

    Me the same. I ended up with the buffer ON and the gain set to 20dB. My only concern was if the output voltage from the Topping A90 (8V) could be a little too high for the input sensivity of the amp at this settings (4V). But in the end I think that 8V output voltage has to be considered at...
  14. M

    Audiophonics HPA-S400ET Review (Stereo Amplifier)

    Could you better explain this? Affect the sound in what aspect? Frequency response?
  15. M

    Audiophonics HPA-S400ET Review (Stereo Amplifier)

    Hi, I need some help. I use a Topping A90 as a preamp connected via XLR to the Audiophonics HPAS400ET. I use the “M” gain setting on the Topping (+6dB). Since my DAC is a Topping D90 connected via XLR (4V out) to the A90, so the output voltage to the Audiophonics amp should be 8V. The...
  16. M

    Dan Clark Audio AEON 2 Noire Review

    @amirm Hi, Amirm, was the preamp level in this EQ settings -6db?
  17. M

    Dan Clark Audio AEON 2 Noire Review

    @Dan Clark Using 1 black felt + 1 foam without EQ could bring similar results to black felt + 1notch white + EQ?
Back
Top Bottom