Search results

Could it be the REW FIR filters? To null latency in Kodi, I must delay the video 250 ms over audio to get sync.

Hi, Just a few words to tell you I have found the solution there https://documentation.help/Virtual-Audio-Cable/glossary.htm#SpeakerPinType. All that was needed is to tick the 'Enable spk pin' in the VAC control panel. Tested it. It survived a power down and a reboot. Kodi still works in...

AH! Thanks Henriq. Wasn't really keen about loopback anyway. It's a dual boot system and the amount of reconfiguration involved is important. Will continue to try to debug the current installation. I know it defies logic, the system looks like it's possessed or haunted but whenever I...

i.e. absolutely nothing happened. no activity in CDSP. like it wan't listening at all. all meters halted in the gui. nothing in the log.

Thanks Henrik, Clear enough. I re-activated the onboard SPDIF output as default device (loopback). I could see the VU meter moving in Windows sound. But CDSP didn't pick it up as capture device. Either a Win 7 issue (unsupported) or my system sound is too damaged. Best!

Windows 7 Update And it's a disaster. After reconfiguring CDSP for 24 bits instead of 16, I had the bad idea to delete from the registry an entry for the CMI8738 in the control panel that wouldn't disappear. After a reboot, strange things started. VLC started playing stereo sounds on all 6...

I don't see anything obvious. Latency is 17 msec for this video. Maybe it's because it's 60 fps. Most of my material is 24-30 fps. 2024-10-23 12:03:37.689 T:45 debug <general>: CActiveAESink::OpenSink - trying to open device PIPEWIRE:alsa-sink 2024-10-23 12:03:37.689 T:45 debug...

I have near zero knowledge on digital audio technicalities. It's only a constatation, an undenyable fact. Depends on the source too. I'm still experimenting. A video from Odysee is not affected. A local video is badly affected: after 2 minutes you want to shut it off: Input #0, mpegts...

Pardon me if those are stupid questions but I'm really wondering as I never tried more resolution than 16 bits and more bandwidth than 48kHz. On linux I tried to set the playback device format (audio card via pipewire) to 32 bits but the increased latency is too important for videos: audio and...

I followed your suggestion and set everything to SE32LE on linux; Win config is yet to be redone. Dual boot system. 3: `Multichannel' Analog audio output on device Xonar D1 -hardware address: hw:1,0 (or hw:D1,0) -formats: S16_LE, S32_LE -usb...

TOSLINK None of that connected I know. Very well aware of the potential issue. The sole ground path to the AVR is via the shileded audio cables to the PC No, it's completely gone the minute I plugged the new card in. Thanks for your assistance.

Xonar D1 arrived today. It's amazing. Same level on analog audio as my onboard S/PDIF, very comparable audio quality (I noticed immediately), no noise (similar to digital). I've regained the 30dB I lost with el cheapo CMI8738 and I can leave the Z906 volume alone, centered as it always was...

If memory serves, the CMI8738 supports only 16. In 2-3 weeks, I'm getting an Asus Xonar D1, which supports 24 @ 192kHz. Tired of all those constant clicks, crackles which seem to be a linux only problem. Always had my Windows record/playback settings set to 16 @ 44.1/48 kHz anyways. Being...

It was worth the wait. Thanks again for your kind guidance. 2024-10-20 14:25:43.425759 INFO [src/bin.rs:781] CamillaDSP version 3.0.0 2024-10-20 14:25:43.427259 INFO [src/bin.rs:782] Running on windows, x86_64 2024-10-20 14:25:43.583779 INFO...

Agreed Thanks so much Totally understandable Best regards, and thank you for that wonderful software.

Nope, not yet, didn't want to bother him with details. He has fully automated builds. I registered (just did) on https://www.diyaudio.com/ but cannot post yet.

As you probably aware of, CDSP 3 for windows now requires Windows 10. I tried cross compiling on a Fedora 40 and it gave me a Win 8 executable. Cannot run because of missing api-ms-win-core-winrt-l1-1-0.dll. 9998 sudo dnf install rustup 10001 rustup-init 10003 source $HOME/.cargo/env 10005...

No log produced. It crashes at start. That's what I was afraid of. Then Win 7 is no longer supported.

Understood. Clear enough, thanks! Unfortunately, CDSP 3 crashes on Win 7. Hopefully it's not compiled with a rust version > 1.75 https://github.com/rustdesk/rustdesk/discussions/7503 In such a case, it ends right there. And impossible to build it, VS 2019, if you don't already have it, is...

Hi Not sure it's the proper place to discuss this. Noticed the beta version and gave it a try. $ journalctl --user-unit=camilladsp --user-unit=camillagui -e --no-hostname oct 15 09:56:35 systemd[2798]: camilladsp.service: Failed with result 'exit-code'. oct 15 09:56:35 systemd[2798]: Failed...