Search results

Good! Thank you!

I’m about to install the 1/4 thick steel legs on the subwoofer. What is best practice to install steel legs one subwoofer? Should I put 1/8 speaker gasket on the touching perimeter in order to stop vibration before screwing them in place? Or the 4x 3/8 bolt securly tighten will keep the legs...

I judge came back to see the measurement in room and just notice that the scale was off. You can see the measurement in the thumbnail, but cumulative one, is 10-300hz. Not very helpful! I’ll turn on my computer and see if I can change the viewing scale!

yesterday night I embedded magnet in the baffle for future grille. One magnet sits a bit proud. Will need to remove and put a new one in. All the others sits 1mm to 0.5mm below the surface of the wood in order to fill it with something to hide the magnet. I don’t k ow how I’ll remove a...

As for the dap product, I purchased the black one. Not the gray like in the picture. Only use this picture to show what company /product. The PL max can be sanded and painted, unlike the dap product. And would only use it between the plate and cabinet on the inside, as per my sketch. And red...

What adhesive should I use to secure it in place? This is a sketch of the cross section: The lip extend 1/2in on every side of the connector. I thought of putting the adhesive in the L corners made by the ABs sheet. These are the two adhesive I have right now: And this is how it’s...

Got to work a bit on the project yesterday. I could pocket out the connector piece I 3d printed.

Testing paint and finish for the speakon connector:

Thought of some cool legs concept too! 1/4 in x 4in flat bar

great build log! I have a pair of 1TD and a 2TD as a center channel and I might upgrade to a full 2tdx for front stage. Love them. They sound really good even the “cheaper” version. The tower must sound complete insane for the price!

Working on it! Also, my speakon connector clears the 3/4 birch plywood:

I know this is not needed, but i felt it was more secure that way considering that I have a 2yo running aorund the house. Doesn<t want them to ug on the cable and whatever could happen. you’re right tho, not the pretties connection, by far. I already have the 90 degrees spekon connector. What...

Yeah. Thought of that. Seen something like this I think it didn’t look bad. Thought of using laser etch aluminum, acrylic or abs.

Can I pick your brain of furniture designer? I am not a huge fan of how I integrate the speakon connector. I dont have a lot of options, but would like to know how would you integrate them in my build. I feel like they were just '' put there''. but I dont want them to ''be in the way'' and to...

I don’t see a huge difference when listening to them with the grill on vs off. I’m pretty sure in a blind test I would fail to know which is which! Kinda surprising result for me too!

Heres the Criton 1TD measurement. Let me know if you want to see something different. Its my second measuring experience. On the left you can read the test I made. 1- woofer with grill, 2- woofer without grill 3- tweeter without grill 4- listening position with grill. 5- listening position...

Oh! Hahaha! In (french canadian) French we say teckel. I have 2 How would you suggest I measure the grills for the critons?

There’s a central divider. But not in angle. I’m not familiar with dackel-design. Haven’t had time to measure the grill. I’ll try tomorrow during lunch. (Trying to find time when baby’s is not sleeping and not home)

Here’s an update on the build. Life got in the way and haven’t touch the subwoofer in a while. Got yesterday and today afternoon to work on it. Made good progress. Yesterday, non of the pannel were glued. Tried to use manufacturer website to drill hole around the baffle opening for screws...

Thanks for chiming in. Our current table is slightly higher than the couch. I was aiming to be at same height as table for the subwoofer.